Guest chpmnsws6 Posted June 14, 2007 Report Share Posted June 14, 2007 Well, It is time to focus on the future, so the drag car must be parted out. Fresh Block and crank with only some engine dyno time on them from SDPC Mahle Coated pistons Mahle rings Callies Compstar rods Clevite bearings ARP main studs .032 gapped top ring .028 gapped second ring All bearings within spec (forget the actual numbers, but were right where they needed to be) Balanced and ready to go 2000 plus shipping New Patriot Performance stage 2 LS6 heads 72cc, but milled .030 7.350 pushrods come with Torqued to block but not ran 900 SHIPPED Meizure Electric Drag Race pump in Black with fittings Comes with proper size lower hose to fit stock radiator 360 SHIPPED FAST 90mm throttle body with sensors 300 SHIPPED Cometic .050 thick gaskets 3.905 bore Torqued once but never ran 125 SHIPPED ARP 6 point head studs Torqued once but not run 200 SHIPPED 242/248 .610/.615 cam on a 111+4lsa 275 SHIPPED Double Roller Timing Chain 100 SHIPPED TH350 transmission conversion Fully built RMVB TH350 with long shaft (so you can use your stock driveshaft) Trans brake SFI Approved bell housing (230 dollar option on top of the normal eBay listed price) 9.5” 3300 stall on a 2.1 STR http://cgi.ebay.com/ebaymotors/GM-T...emZ170119334643 BMR TH350 conversion cross member TCI SFI Approved Flex plate ARP Flex Plate Bolts Hurst Quarter Stick B&M Pro Ratchet Shifter (will give both so you can decide which one you like best) 2400 plus shipping Moser 9 inch rear end Narrowed 1.5 inches on each side Nodular Center Housing Aluminum Spool Moser Yoke 4.0 gears 31 Spline Moser Axles ARP Wheel Studs 4 channel ABS ready 3 inch Balanced Chromoly Drive Shaft for shorter Moser Yoke 2100 plus shipping (I also need your LS1 backing plates, as I will be giving my LS1 backing plates to you) Black Alston Torque Arm- 300 SHIPPED Trackbird Heim Jointed Lower Control Arms with bolts- 125 SHIPPED Heim jointed Panhard rod- 125 SHIPPED Spohn 25mm rear sway bar- 140 SHIPPED Strange single adjustable rear shocks (have some rubbing where the sway bar was rubbing it, but no damage was done) 3500 miles max- 200 SHIPPED Afco front shocks with 250 pound springs Ready to install (already assembled) 500 SHIPPED Synergy Nitrous M6 2-step Stand alone PCM engine wiring harness with wires ready to install 2 step. All that you need to run the car is a 12 volt switched and 12 volt hot all the time wire with this harness. It has dual fan controls. All emissions removed. HPTuners with 2.18 update and the Speed Density Tuning option (1.7 I think?) It also has EV6 injector clips so you can run 39 pound 03-04 cobra injectors, which I will include with this package 1150 SHIPPED for the package 6 Convo Pros 2- 15x4’s with NEW Kumho 758’s 2- 15x8.5’s with BFGoodrich Radial T/A (same size as 28x11.5 slick) 2- 15x10’s with 28x11.5x15 Hoosier Quick Time Pros Both sets of rears have 5 inches of backspacing 1100 plus shipping for all 6 with center caps and lugnuts Speed Inc Fuel Cell that fits stock location with stock filler neck A1000 Fuel Pump Aeromotive Fuel Filter A1000 Fuel Return Black AN8 Pushlok Pressure Black AN6 Pushlok Return All cut and ready to be installed onto your fuel rails. Will also include connectors ready to be installed onto car for quick and simple installation 1000 SHIPPED Kirkey Seats with Black covers Drivers side has brackets already made for stock seat studs 350 plus shipping Manual brake cylinder. Will also include pre cut lines so you have new hard lines, with OEM fittings 250 SHIPPED 99+ fuel “bucket” with 255 Walbro pump installed. All large wire run, so you can hotwire the pump for zero voltage drop. It also comes with the fuel level sender. Ready to drop in and go. 175 SHIPPED 255 Walbro pump 100 SHIPPED Aftermarket gauge cluster TPIS 120mph electronic Speedo Equus Water temp gauge Equus Fuel Level Gauge (240-90ohm) (will read F when E, but will be correct in opposite sweep) Equus Volt Meter Gauge Equus Oil Pressure Gauge Red Light for SES Blue Light for Bright Indicator Lamp Green Lights for Turn Signal Indicator Lamps Will also include 0-90 ohm Fuel Level Gauge 300 SHIPPED Eldebrock Stainless Steel Stepped Headers with 3 ½ in collectors Has 3 ½ inch spiral flow mufflers the slip on collectors. Spiral Flows have turndowns welded to them. Still needed O2 sensor bungs welded up, so you can have them where you want or need them. Will include bolts, gaskets, and clamps 700 plus shipping Coil Pack relocation kit, WITH coils. Uses some of the best wires ever made. Dirt Track racers will just let these wires lay on the headers, and never have a problem with them. Wires are red, with grey boots. 225 SHIPPED LS1 Front and Rear Brakes. Has NIB pads waiting to go on 350 SHIPPED PA-Racing K-member and A-arms Black, Mild Steel. LS1 mounts with Stock Steering Rack 700 plus shipping Poly Motor Mounts already installed in the clamshell No need to drill out old rivets, cuss at new mounts, or fight putting poly inserts into stock clamshells 70 SHIPPED 2000 Trans Am WS6. Artic White, Originally a 6 speed 40,000 miles on chassis Custom body wiring harness Flaming Rivers Shut Off Switch with Pushrod BMR boxed SFC’s 6 point cage Ozite carpet VFN WS6 Pin On hood installed All weight reduction done Stock gutted dash, stock gauge cluster. Perfect for someone who wrecked there 99-00 6 speed trans am, and wants to get into a lighter car with roll bar and weight mods already done 3000 OBO. Must come pick up, as it has no K-member or rear end. Will also include all nuts, bolts, and any other parts gathered from years of LS1 wrenching Title in hand Link to comment Share on other sites More sharing options...
MrMeanGreen Posted June 14, 2007 Report Share Posted June 14, 2007 I replied to you on LS1Tech. Lemme know. Link to comment Share on other sites More sharing options...
Guest Wunna Dig Race Posted June 14, 2007 Report Share Posted June 14, 2007 Pics? Link to comment Share on other sites More sharing options...
Guest chpmnsws6 Posted June 14, 2007 Report Share Posted June 14, 2007 Reply sent on LS1tech What would you like pictures of? Link to comment Share on other sites More sharing options...
Guest 5.7 Posted June 14, 2007 Report Share Posted June 14, 2007 would you split up the tires/wheels? Link to comment Share on other sites More sharing options...
Guest chpmnsws6 Posted June 14, 2007 Report Share Posted June 14, 2007 If you want both sets of rears, yea two other guys have dibs on the fronts if i decide to split them, but won't untill the rears sell Link to comment Share on other sites More sharing options...
Guest 5.7 Posted June 14, 2007 Report Share Posted June 14, 2007 can you pm me a price(for the rears) and pics to deejayy02@yahoo.com .. I will need a set for my Camaro.. Link to comment Share on other sites More sharing options...
Linn1647545492 Posted June 14, 2007 Report Share Posted June 14, 2007 Does the K memeber have the motor mounts and is this for the upper and lower A arms? Link to comment Share on other sites More sharing options...
MrMeanGreen Posted June 14, 2007 Report Share Posted June 14, 2007 PM me your #.... Link to comment Share on other sites More sharing options...
AJ Posted June 15, 2007 Report Share Posted June 15, 2007 if anyone wants the body i have the entire stock front suspension set-up that will fit this car. i'd buy it if i had the cash. Link to comment Share on other sites More sharing options...
Guest chpmnsws6 Posted June 15, 2007 Report Share Posted June 15, 2007 Does the K memeber have the motor mounts and is this for the upper and lower A arms? It has LS1 motor mounts and just the lowers. Uppers don't save you any weight, and can actually add weight in mild steel 700 for the rear tires if you come get them Link to comment Share on other sites More sharing options...
Amy Posted June 16, 2007 Report Share Posted June 16, 2007 Chris get ahold of me.. I want the Hoosiers! ASAP! Link to comment Share on other sites More sharing options...
muscless Posted June 19, 2007 Report Share Posted June 19, 2007 Is the rear still for sale Link to comment Share on other sites More sharing options...
Guest chpmnsws6 Posted June 20, 2007 Report Share Posted June 20, 2007 Who's chris? The rear end is pending Link to comment Share on other sites More sharing options...
Recommended Posts