ProwlerZ Posted July 2, 2008 Report Share Posted July 2, 2008 Alright, this is my last shot on here before I just pack it up and carry it with me for the move. I am taking a big loss here as is, but as a final effort, I'll sell it for $300, with the O2 plug, and if you need the block off plates and wing nut fasteners for the cutouts, I'll include them for $20 more (which is what it'll cost me to buy a new pair). PM with questions. Somebody has to be looking for a solid exhaust setup! http://i113.photobucket.com/albums/n210/drsites/DSC04457.jpg http://i113.photobucket.com/albums/n210/drsites/DSC04460.jpg http://i113.photobucket.com/albums/n210/drsites/DSC04461.jpg http://i113.photobucket.com/albums/n210/drsites/DSC04459.jpg I recently lowered my car and decided I wanted more clearance, so i've replaced it with an ORY and catback system, and the my custom duals are up for sale. Here's the general setup: 3" i.d. piping to connect to 3" Long tubes (I have QTP LTs, so they're a pretty common length) reduced to 3" o.d. piping Dual cutouts at first turns, I ran dual electrics, though I'm using them on my new setup, so they're not included. Dr. Gas X-pipe, 3" in/out Magnaflow 14"x9" Stainless Steel single chambers Turndowns before axle (dumped) This system sounded very good, I always got compliments, and I will deeply miss it, though when finances allow, I'll have the same thing fabbed up with ovaled piping for better clearance. I almost never scraped at stock rideheight, but the pro-kit dropped it too much, and I don't want to have to worry this much. This system has scraped stuff, but has no substantial wear, minus one notable dent where one of the mufflers hit something, but nothing effecting flow, sound, or integrity. I also have an O2 bung welded in the system on the driver's side, I was running a wideband. I could meet someone somewhere, but would prefer pickup (NW columbus, bethel rd area). I'm selling it with an O2 bung plug, and if you need the cutout blockoff plates, I'm willing to discuss parting with them. Don't lowball me, but if you have an offer, make it! Link to comment Share on other sites More sharing options...
Guest Removed Posted July 2, 2008 Report Share Posted July 2, 2008 pm yellowsnake..i think he is looking for this setup! Link to comment Share on other sites More sharing options...
yellowsnake Posted July 2, 2008 Report Share Posted July 2, 2008 damn you i just bought mine from someone. Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 2, 2008 Author Report Share Posted July 2, 2008 ttt.... any interest? It's off the car, I just have to clean it up if people want pics... Link to comment Share on other sites More sharing options...
Jizzle Juice Posted July 2, 2008 Report Share Posted July 2, 2008 Can i get pics please!! Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 19, 2008 Author Report Share Posted July 19, 2008 Ttt, pics added, I want to get this sold ASAP... Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 19, 2008 Author Report Share Posted July 19, 2008 TTT... any interest? I'm taking offers at this point, I don't want to have to take this with me when I move... Link to comment Share on other sites More sharing options...
Reed44 Posted July 21, 2008 Report Share Posted July 21, 2008 Will it fit pascessetter LT's? Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 22, 2008 Author Report Share Posted July 22, 2008 The only headers I've heard that it won't fit are the old style SLP headers. I had this set hooked up to 2 sets of QTP LTs, and one set of SLP new style headers, no problems on any of them. I'm also now throwing in the O2 plug, in case you don't have a wideband, and if needed, I'll part with the block off plates too. All you need to use this exhaust is a pair of universal hangers to bolt up to your car, then Presto, you're car sounds badass! Link to comment Share on other sites More sharing options...
ruinms Posted July 23, 2008 Report Share Posted July 23, 2008 u have pm Link to comment Share on other sites More sharing options...
Reed44 Posted July 23, 2008 Report Share Posted July 23, 2008 So is that a yes or no on the pascessetter? I can measure them thursday and see how far apart they are if that will work. Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 23, 2008 Author Report Share Posted July 23, 2008 Measurements I just took from the duals themselves: -Outside to outside= 30.5" - Inside to inside= 24.75" If your measurements are within I'd say 1/4", these should slip right on, less than 1/2" and they'll still work as is, but more than that, you're probably going to need a little pipe tweaking to mate up. Rememer that this system is 3" ID piping at the ends, so it'll slip over 3" LTs, so you're actual header to header measurements will simply fall within the range (i.e. the outer to outer measurements should be about 1/4" shorter, and your inner to inner should be roughly 1/4" bigger). PM me with any other questions. If your measurements turn out to be out of range, please let me know so I can redirect the application! Link to comment Share on other sites More sharing options...
Reed44 Posted July 23, 2008 Report Share Posted July 23, 2008 Thanks. I will take measurements and contact you. Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 25, 2008 Author Report Share Posted July 25, 2008 Ttt.... anybody take measurements of their systems? Link to comment Share on other sites More sharing options...
ProwlerZ Posted July 29, 2008 Author Report Share Posted July 29, 2008 TTT.... I'm going to list this on Craigslist and Ebay (as a set price auction), and if nobody bites, I'll take it south with me. I've had enormous interest elsewhere, but I don't want to have to hack this thing up to ship it, and I know somebody here is wanting duals! Link to comment Share on other sites More sharing options...
Reed44 Posted August 22, 2008 Report Share Posted August 22, 2008 Do you still have it? I didnt mean to bug out last time on it but thats when my rod bearings went so exhaust had to wait. Now its time to get a new exhaust so.... Link to comment Share on other sites More sharing options...
Recommended Posts