KillJoy

After looking.....I think I may be out as well. It does not look like there is any EASY source for frangible bullets for reloading. I am not going to pay $20+ for 50 rounds for a day of shooting. I can reload 45 Lead SWC for <$10 / 50. Unless a CHEAP source of ammo is found...I am out. KillJoy PS - Sorry...

Very interesting.... I would consider joining, depending on the other attendees. Some here should not be behind the wheel of a car....let alone a firearm How far in the future are you looking? Most all of the loads I have worked up are for 200gr Lead SWC. Shouldn't be too hard to work up a new load. I have never heard of this range (not a suprise). Are they normally open to the public? Do they offer Memberships? What are the rates? This is much closer to me than The Powder Room. And if it is a "private" club....I would be VERY interested in joining (if possible). I hate some of the dumbasses that are at the PR on a daily basis. KillJoy

What are you consufed about? I want the piece that the Seat Belt buckles in to, for the Drivers Side. I am also interested in BOTH Headlight Assemblies, if they do not fog up. KillJoy

How much do you want for the Latch Portion of the Drivers Side Seat Belt (The part that is on the right side of the seat, as you are sitting at the wheel)? KillJoy

I recommend Jeff at DynoTune Motorsports. He just installed 4.10's in my Marauder (Ford 8.8").....no problem at all!!! Drop them a line.....let them know I said to call Brian Turner; Owner and Ford Tuner 614-778-8984 brian@dynotunemotorsports.com Howard Turner; Owner 614-778-7823 howard@dynotunemotorsports.com KillJoy

Awwww....it's so cute! KillJoy

Congrats on the proposal!! It takes major nutz.....especially in from of a crowd Best of luck to you, and the misses, for the future!!! KillJoy

Currently, the Trilogy if a single screw. They are working on a twin. That will be a BITCHIN' setup! KillJoy

Or Best Offer KillJoy

Edited to reflect CORRECT pricing. KillJoy

Actually.....AFAIK, there are already some who have installed a KB Twin Screw on their Marauders. I know there are at least 2 Marauder Vendors in the development stages of these kits as well. Bottom ends are going to need to be built for these...or grenades are going to happen! KillJoy

Yes....there are Imp SS running manual Trannies. There is a SS Forum that has some local members. The local Marauders have had Lunch before w/ them, and some of their cars are set up nice! KillJoy

+1 Dick Doctor KillJoy

I just upgraded to 4.10's in my Marauder, so these are just laying around. It is the Stock Factory Ring and Pinion (3.55 Ford 8.8). No bearing, washers, spacers.....nothin' else. These have 41,500 miles on them. $1,000,000 OBO KillJoy

Call a HVAC guy. Some offer FREE estimates (ie - All Knight). Messing w/ gas.....when you have no clue what your are doing, is a BAD thing KillJoy

Bump for a nice car. KillJoy

You need to register to view those pics. KillJoy

I am running out of room, and this project may take me a while to finish. I am just looking to see if there would be any interest in this here. I have a gutted Arcade Cabinet. The Coin Mech is there, but someone has drilled some holes in it. ALL laminated surfaces need to be repalced. This was from a game called Tic Tac Trivia. I also have: X-Arcade Dual Controller 19" or 20" Flat CRT Monitor (I can check size if anyone really cares) Set of cheapie speakers w/ a sub Dell 900MHz PC, I forget the amount of RAM or HDD size, but it plays MAME just fine. I am not gonna lie, some work is needed here. I would like $200, and you come and get it. The X-Ardace is $130 new, and this one had barely been used (only played around with it when I first got it). Let me know... KillJoy

No problem. KillJoy

I'm interested. Looking for a beater. Motor Stock? Trans Stock? Milage? Pics KillJoy

Yeah.....this isn't gonna lead to any retaliation..... KillJoy

Bump

I am interested. How flexible is your OBO? KillJoy

Correct...STOCK, they are NOT supercharger. Mine is NOT stock KillJoy

Here is my delima.... I have an '03 Mercury Marauder. My Exhaust options are as follows: Install Kook or Stainless Works Long Tube Headers, and their X-Pipe (w or w/o Cats) Install Cobra Manifolds, and a Magnaflow 93335 Catted X-Pipe or Have a Custom Catted X-Pipe constructed to the stock Manifolds NO aftermarket X-Pipe will mount to the Factory Manifolds. I am not looking to increase the sound (yes...I am sure it will increase some), but to free up a little power. The stock tubing from the Manifols to the Mufflers is 2 1/4". Mufflers back is 2 1/2". Also, there are 2 Cats on each side. I would like 2 1/2 Manifold back, with some High Flow Cats installed. KillJoy