redbarron77 Posted July 14, 2014 Report Share Posted July 14, 2014 Long story short, the bolt that holds my tank on broke off. How can I get this out to put in a new one, or should I take this to someone who knows what they are doing? FYI - I changed the spark plugs last year, and that is probably the upper end of my mechanical skills. Quote Link to comment Share on other sites More sharing options...
Tpoppa Posted July 14, 2014 Report Share Posted July 14, 2014 Can you post a photo? There are lots of different tools to remove broken bolts. Quote Link to comment Share on other sites More sharing options...
gsxkat1100 Posted July 14, 2014 Report Share Posted July 14, 2014 It really depends on how much of the bolt is still hanging out. Is it broken flush? Or is there some threads sticking out? Can you grab remaining bolt with vise grips? (I do not recommend this, as I use bolt extractors.) Quote Link to comment Share on other sites More sharing options...
redbarron77 Posted July 14, 2014 Author Report Share Posted July 14, 2014 I'll grab a photo at lunch. Quote Link to comment Share on other sites More sharing options...
3.504 Posted July 14, 2014 Report Share Posted July 14, 2014 Few different extractor styles, usually require drilling bolt. Can also get reverse drill bits.If there is some of the bolt hanging out, then you can grab with grips and try. Bolt may be seized in frame though, which means its going to fight you. Get some pb blaster and soak it. Sometimes I soak a rag with blaster, then set the soaked rag on the bolt for a few hours. Last resort: drill it all the way out, thread chase or if you have to drill that big: helicoil Quote Link to comment Share on other sites More sharing options...
Gixxus Christ! Posted July 14, 2014 Report Share Posted July 14, 2014 Did it snap while being tightened or loosened? Quote Link to comment Share on other sites More sharing options...
redbarron77 Posted July 14, 2014 Author Report Share Posted July 14, 2014 Short story long: Was riding along, and when I slowed down for a red light, heard some really bad rattling sound. Pulled off the road, and I thought the bolt had loosened and run itself out. When I had a chance to look at it yesterday, found the damn thing had snapped off! Last time I did anything with this bolt was last spring when I changed the plugs out. I didn't think I overtightened it, but I must have. you can see the bolt is shorn off. even with the tank in the way, you can see the bolt broke down in the threads of the hole(there is probably some mechanical term for this, but I am not mechanically inclined). Any ideas, or do I take it to someone who knows what they are doing? Quote Link to comment Share on other sites More sharing options...
Gixxus Christ! Posted July 14, 2014 Report Share Posted July 14, 2014 Shouldn't be too hard. You can try to turn it out with some punches, just find a low spot and put a dimple there, then use a punch and hammer to try and turn it out. Another option would be if it's a through hole to try and turn it out the other side. An ez out would work too. Where are you located? Quote Link to comment Share on other sites More sharing options...
redkow97 Posted July 14, 2014 Report Share Posted July 14, 2014 pick up some extractor bits, and be sure to use the drill-bit they recommend! I have used these with success in the past on brake caliper bolts that I over-tightened and snapped off. Ordinarily I would advise heating the bolt before extracting, but flame + gas tank is probably not a great idea. Hair dryer or heat gun would do something, but not much... Spray the shit out of it with penetrating oil, and let it set over night. Then drill the bolt, tap in the extractor bit, and twist slowly with a socket wrench. good luck. Quote Link to comment Share on other sites More sharing options...
redbarron77 Posted July 14, 2014 Author Report Share Posted July 14, 2014 I'm in Texas, but thanks for the ideas on the extractor bits! I'll give it a try, and just for posterior's sake, I plan on removing the tank. Quote Link to comment Share on other sites More sharing options...
jacobhawkins Posted July 15, 2014 Report Share Posted July 15, 2014 I work at a job shop machine shop and we get this kind of thing in occasionally. If you don't have luck with your extractors, I'd see if there are any shops around that might be able to help. Bolts are not usually hardened, but if you get the threads screwed up enough to need a helicoil, it might be wise to have somebody put that in for you. Good luck! Quote Link to comment Share on other sites More sharing options...
Helmutt Posted July 15, 2014 Report Share Posted July 15, 2014 (edited) Likely a grade 8.8 metric M6 or M8. Penetrating oil bath and extractor kit would probably suffice, and gives you a reason to buy an extractor kit for any future issues.I like having reasons to buy new tools Edited July 15, 2014 by Hellmutt 3 Quote Link to comment Share on other sites More sharing options...
redkow97 Posted July 15, 2014 Report Share Posted July 15, 2014 keeping a couple of extractor bits in my tool box has prevented any bolt breakage for me since I twisted off the caliper bolts in my 600RR in 2011, I believe. It's like bringing an umbrella to ensure that it doesn't rain... Quote Link to comment Share on other sites More sharing options...
blueskeyes Posted July 16, 2014 Report Share Posted July 16, 2014 EZ-Out kit. Use one drill bit size smaller than recommended (e.g. use #31 if #30 called out for) for maximum effectiveness and push down hard while turning the extractor. Quote Link to comment Share on other sites More sharing options...
redbarron77 Posted August 4, 2014 Author Report Share Posted August 4, 2014 followed the advice here, got self tapping extractor set and put in the pilot hole for safety: decided to use the smallest extractor, 6 mm, and about 10 seconds into the "Tapping" faze, the drill jerked forward. My first thought was "I just ruined the threads on this!" (along with a few choice expletives) The broken part of the bolt fell through the hole and down to the ground. The bolt remains are on the right.... Thanks for all the suggestions, and now the bike is as good as new! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.