TurboRust Posted July 6, 2010 Report Share Posted July 6, 2010 I have no time right now or in my near future to road race this car like I built it to. Therefore I'm posting a feeler to see if there would be anyone interested in trading for something with a drag setup, or buying outright. mods are as follows: 91 rx7 black/black originally an auto car from Georgia swapped to 5spd zero underbody or frame rust. car has paint and lots of it, meaning it was a maaco job at best. all body parts/mods have under 2000 miles on them Front and rear pads and rotors, with stainless lines(4 piston fronts) koni yellows with eibach ground control coilovers front camber plates(well used not under 2k miles) rear sway bar deleted(still have) rear toe eliminator bushings new rear hub bearings longer studs installed fenders rolled(front dented while rolling so I bought the fiberglass ones) fiberglass 30mm flared front fenders(not installed and need paitn) big alum radiator with taurus fan factory gas and oil pressure gauges work aftermarket tach, autometer coolant and 30 psi boost gauges innovative wideband with blue gauge walbro 255hp fuel pump with upgraded wiring to 10 gauge pioneer stereo that could use replaced sunroof(doesn't open needs pulled apart and lubed up) 17x9 mb wheels fr: 245-40-17 bridgestone re-01r(brand new) re: 255-40-17 toyo r888 (road racing tread left..2/32nds) factory 15"s with 195-60-15 all seasons(40% tread) Drivetrain 88 2.3 turbo block and head ranger roller cam with adj gear retarded -4* .60-.48 t3 at 15psi (makes about 220whp and 280wtq) kirban adj fpr stock 36lb/hr injectors(extra 3 included) sheet box upper with 65mm tb knife edged ported lower(all 1 pc. welded) ported rfe6 exhaust manifold big k@n fmic using 2.25 pipe and a grand nat'l core with custom endtanks 3" down pipe catless 3-2.5" y pipe at rear dual stainless magnaflows with 4" dual rolled wall tips catch can wc t-5 trans new clutch new hydraulic slave cylinder new hydraulic slave master braided stainless clutch line custom driveshaft made by columbus joint and clutch 88 gtu clutch type locking rear end head gasket, bolts, waterpump, thermostat, hoses, plugs, wires, cap, rotor, timing belt all new Thats a depressing list. There are countless hours of fabrication done myself and Tinman, and I have over $5000 in parts, but I'm not expecting that much. The car is a little rough around the edges but would be perfect for roadracing and a fun summer street car, thats what I built it for. It just seems drag racing fits my busy schedule and budget a little more than road racing does. So I'll trade for a well prepped foxbody or something with a solid rear that can be modded for 1.4x 60's.. or sell for $4300 with the 17x9 wheels or $3900 with the 15 inch stockers Current wheels http://www.columbusracing.com/forums/picture.php?albumid=214&pictureid=3936 old wheels http://www.columbusracing.com/forums/picture.php?albumid=214&pictureid=1848 http://www.columbusracing.com/forums/picture.php?albumid=214&pictureid=1849 Link to comment Share on other sites More sharing options...
SPL_Josh Posted July 6, 2010 Report Share Posted July 6, 2010 Nice car glws Link to comment Share on other sites More sharing options...
Sam1647545489 Posted July 6, 2010 Report Share Posted July 6, 2010 Any pics of the engine bay to see how the swap looks. Link to comment Share on other sites More sharing options...
TurboRust Posted July 6, 2010 Author Report Share Posted July 6, 2010 couple slightly old engine shots.. will have fresh ones up in a couple days stuff is painted/ cleaned a little nicer, and intercooler piping is welded together http://www.columbusracing.com/forums/picture.php?albumid=214&pictureid=1339 http://i37.photobucket.com/albums/e91/Turborust/fcengine.jpg 1 Link to comment Share on other sites More sharing options...
FST94TSI Posted July 7, 2010 Report Share Posted July 7, 2010 I know the add says original georgia car but did this by chance come from here in town more recently. I sold one for a friend of mine a couple years back that had a blown rotary (imagine that). Im pretty sure some CR guys bought it. It was sold from a neighborhood up off of cleveland ave. in westerville if this is the one. Link to comment Share on other sites More sharing options...
TurboRust Posted July 7, 2010 Author Report Share Posted July 7, 2010 I got it from nate..it was in Johnston for awhile Link to comment Share on other sites More sharing options...
neonkiller Posted July 7, 2010 Report Share Posted July 7, 2010 Biump for a sic car! Link to comment Share on other sites More sharing options...
Rally Pat Posted July 7, 2010 Report Share Posted July 7, 2010 Hmm still never got to see this car. Good luck with the sale though. Definitely on my "things to build" list. Link to comment Share on other sites More sharing options...
Nate1647545505 Posted July 7, 2010 Report Share Posted July 7, 2010 I know the add says original georgia car but did this by chance come from here in town more recently. I sold one for a friend of mine a couple years back that had a blown rotary (imagine that). Im pretty sure some CR guys bought it. It was sold from a neighborhood up off of cleveland ave. in westerville if this is the one. It was actually purchased from Lee Bevins (wive's car), who did alot of art for GM, USAF, etc.. Link to comment Share on other sites More sharing options...
TurboRust Posted July 7, 2010 Author Report Share Posted July 7, 2010 It was actually purchased from Lee Bevins (wive's car), who did alot of art for GM, USAF, etc.. in georgia...lol Link to comment Share on other sites More sharing options...
TurboRust Posted July 10, 2010 Author Report Share Posted July 10, 2010 lock it up.. car is staying with me but getting a new heart. Link to comment Share on other sites More sharing options...
Recommended Posts