Mattsv8 Posted October 18, 2011 Report Share Posted October 18, 2011 Hey guys I need to make a pipe to delete my frozenboost intercooler and see if its the reason I can't make power past 15psi. I need a 3.5" 180deg bend short legs would be fine just the 180 and enuf straight section for a bead roll and a silicone coupler on each end is all I need. If anyone has one I could use it asap. Gona try and test without the cooler for a few runs. Link to comment Share on other sites More sharing options...
coltboostin Posted October 18, 2011 Report Share Posted October 18, 2011 You can just run some calculations and answer that yourself! What is the core rated to flow? What model you rocking? I will check storage to see if I have the pipe BTW Link to comment Share on other sites More sharing options...
pdqwagon Posted October 18, 2011 Report Share Posted October 18, 2011 Any way you could put it back the way it was before the cooler or is that pipeing gone? Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 18, 2011 Author Report Share Posted October 18, 2011 Its not gone but I cut the stock tube up to make the mt for the new intercooler setup. It is the model5 wich flows 1500. In therory I'm at 1500cfm at 15.5 + and I'm not seeing any power past that reading boost from below carb. I could tap it and check pre core boost pressure too but I wana make shure I have a deletion pipe on hand just in case. It really seems way to small for a88mm. Core is only 10x9x4.5 I believe. And there is a bunch of people who say me being carbed and e85 and rich shouldn't need it at all below 25psi Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 18, 2011 Author Report Share Posted October 18, 2011 If it really does run better without it I will be building a new direct to carb pipe like it was before. Would be nice if I don't need it cause the thing is like 30 plus lb plus ice and eater pump and 35 ft of 5/8 heater hoses. http://i33.photobucket.com/albums/d71/Mattsv8_03/SSPX4702.jpg This is how it is now gona add a simple 180 bend and test http://i33.photobucket.com/albums/d71/Mattsv8_03/SSPX0354.jpg This is how it was before. Went 9.0s this way and best of 8.89 with it but I changed a lot tooso no way to say the ic helped at all. Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 18, 2011 Author Report Share Posted October 18, 2011 If it really does run better without it I will be building a new direct to carb pipe like it was before. Would be nice if I don't need it cause the thing is like 30 plus lb plus ice and eater pump and 35 ft of 5/8 heater hoses. http://i33.photobucket.com/albums/d71/Mattsv8_03/SSPX4702.jpg This is how it is now gona add a simple 180 bend and test http://i33.photobucket.com/albums/d71/Mattsv8_03/SSPX0354.jpg This is how it was before. Went 9.0s this way and best of 8.89 with it but I changed a lot tooso no way to say the ic helped at all. Link to comment Share on other sites More sharing options...
Alex L. Posted October 18, 2011 Report Share Posted October 18, 2011 I can get you a new bend. Link to comment Share on other sites More sharing options...
TurboNova Posted October 18, 2011 Report Share Posted October 18, 2011 Racepart solutions or chassis shop has quick shipping Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 18, 2011 Author Report Share Posted October 18, 2011 A ayell the tubbing on it is frome racepartsolutions but was hopping someone local has it How much? If I don't find one tomorrow ill have to order from racepart and hope I can get it here cut it and. Get it bead rolled by next Friday! Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 18, 2011 Author Report Share Posted October 18, 2011 I was just hopping someone local had it so id have time to bead roll it and make it fit. All the alum tubbing is racepartsolutions tubbing. I just wana make shure I have it done before next friday Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 19, 2011 Author Report Share Posted October 19, 2011 ok guys i orderd a new 3.5" 90 on ebay. for some reason the only alum 180s racepart shows is 2.5" but the shipping said wont be here till nov 7th to 14th. so anyone got a 3.5" alum 180 or 2 90s i could use till oct 29th Link to comment Share on other sites More sharing options...
y2k2gt Posted October 19, 2011 Report Share Posted October 19, 2011 http://www.mandrelbendingsolutions.com/servlet/the-334/Aluminum%2C-Mandrel%2C-Bend%2C-Bends%2C/Detail Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 19, 2011 Author Report Share Posted October 19, 2011 Yea I checked there too almost 40 bucks wo shipping Link to comment Share on other sites More sharing options...
BDHG940 Posted October 19, 2011 Report Share Posted October 19, 2011 this is where I get everything, his inventory is always changing so I order ahead of time mostly. You cannot find it cheaper for the same grade he sells http://www.ebay.com/sch/boeschbuilt/m.html?_trkparms=65%253A12%257C66%253A2%257C39%253A1%257C72%253A5476&rt=nc&_trksid=p3911.c0.m14.l1581&_pgn=2 Link to comment Share on other sites More sharing options...
Mattsv8 Posted October 20, 2011 Author Report Share Posted October 20, 2011 Looking likle ill have to rock the intercooler at this deal. Can't find any 3.5" hmm maybe truck pro has aluminized steel 3.5" Link to comment Share on other sites More sharing options...
Mattsv8 Posted December 6, 2011 Author Report Share Posted December 6, 2011 never got the bend off ebay over 1 mth so paypal just returned the money to me. turns out i deleted the ic now i can just make a small turbo to carb pipe like it used to be. anyone got any 3.5" alum bends at all lying around 45s or 90s 3m thick Link to comment Share on other sites More sharing options...
spooling 1g Posted December 7, 2011 Report Share Posted December 7, 2011 Any diesel shops around you?They should have them. Link to comment Share on other sites More sharing options...
Recommended Posts