rb26deet32 Posted September 4, 2012 Report Share Posted September 4, 2012 I'm parting out my race car because I'm not longer into the build. The build is a caged 92 civic hatch back with a fully built turbo lsvtec. I will either sell everything out right for the right price or I will be parting everything out. I'm looking for a new daily. Needs to have ac and get good gas mileage. Besides that it doesn't really matter. Thanks. 1992 Honda Civic Si: $2,000 OBO with everything listed -6 point roll cage -battery relocated to the rear bumper when it has battery terminals and a shut off switch wired up -Car also has a hole cut for a 10 gallon fuel cell. If you do not want a fuel cell I can weld the plate back in no problem -The car has coil overs on eibach springs on stock control arms -Drag dr31 wheels with bfg 205/50/15 traction ta's -gsr rear disc swap -S2000 brake reservoir with larger diameter brake lines and braided brake lines at each caliper -The carpet is stripped out except for the driver seat area but all the plastics are still there and matching -Integra ls seats in there but I can throw in some rsx seats if you'd be interested -The center dash also has holes for 4 gauges -The title is clean and clear. BAD: -The paint is newer but unfortunately the people that did the body work must have missed a little rust because there is a bubble on the left rear quarter panel. It's not flaking but it is bubbling. http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/civic1.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/civic2.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/civic3.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/civic4.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/civic5.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/civic6.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/12.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/13.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/9.jpg Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 4, 2012 Author Report Share Posted September 4, 2012 B18b1 Short Block: $2,000 OBO (will cost at least $3,100 any where else) -0 miles since rebuild (bored to 81.5mm, hot tanked, honed, decked, blue printed and balanced) -81.5mm CP 9.0:1 pistons -Eagle rods -Honda/ACL bearings -New oem water pump/oil pump http://i35.photobucket.com/albums/d153/rb26deet32/Stuff%20For%20Sale/IMG_20111026_192646.jpg http://i35.photobucket.com/albums/d153/rb26deet32/Stuff%20For%20Sale/IMG_20111026_205019.jpg P72 (GSR Vtec) Head: $1,200 OBO OBO -0 miles on it since all the work was done by Slowmotion Motorsports in Sunbury Ohio -Stage 3 port and polish on intake and exhaust side -Supertech valves, valve springs -Honda retainers and keepers -Accord lma's -Vtec solenoid -Clean oem looking valve cover -NGK spark plugs and wires http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_20111026_205238.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_20111026_205227.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_20111026_205127.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/gsr2.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/gsr3.jpg Precision SC6176 journal bearing turbo: $500 OBO -less than 100 miles on it -Good for 680hp http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/aaaa.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/aaaaa.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/aaaaaaa.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/aaaaaa.jpg Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 4, 2012 Author Report Share Posted September 4, 2012 Neukin Mini ram manifold and 3" v band down pipe $500 OBO -Works with any b series engine -V band down pipe and wastegate -less than 100 miles on manifold -Down pipe matches manifold and clears oil pan perfectly -Down pipe has flex pipe and about 8 feet of 3" straight pipe exhaust http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/aaa.jpg http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1476.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/exhaust1.jpg Precision 46mm Wastegate: $275 OBO -less than 100 miles on it (no dump tube) http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1689.jpg Tial 50mm Bov: $100 http://i35.photobucket.com/albums/d153/rb26deet32/Stuff%20For%20Sale/IMG_20120903_204122.jpg Hasport b series in eg mounts: $300 -Brand new, never been used. Stiffest material besides a solid mount. http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/mount1.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/mount2.jpg http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/mount3.jpg Black nylon braided -10 -8 fuel lines and AN fittings: $500 OBO -Brand new, never had gas through it http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/fuel6.jpg Aeromotive Fuel pump and controller: $250 each or $450 for both http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1692.jpg Aeromotive FPR: $100 http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1733.jpg Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 4, 2012 Author Report Share Posted September 4, 2012 MSD cap and external coil for B18b: $100 OBO http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1542.jpg Supertech intake and exhaust valves for b18: $200 OBO -Used but came out of a working car http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1737.jpg ARP Head studs for a b18b1: $75 -Torqued properly one time http://i35.photobucket.com/albums/d153/rb26deet32/92%20EG%20Build/IMG_1740.jpg B16a2 short block (no rods/pistons): $100 http://i35.photobucket.com/albums/d153/rb26deet32/Stuff%20For%20Sale/IMG_20120903_203919.jpg DSM side mouth intercooler: $25 http://i35.photobucket.com/albums/d153/rb26deet32/smic1.jpg HF Manifold and adapter plate: $25 http://i35.photobucket.com/albums/d153/rb26deet32/hfmani.jpg Catch can and lines: $50 http://i35.photobucket.com/albums/d153/rb26deet32/Stuff%20For%20Sale/IMG_20120903_203947.jpg Pro Comp Oil pressure gauge: $40 http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/gaugeoil.jpg Sun pro oil pressure gauge: $25 http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/gaugeoil2.jpg Sun pro water temp gauge: $25 b16 intake manifold: $25obo http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/IMoem.jpg B series axles: $25 per set http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/axles2.jpg 2 B18b engines harness: $75 obo per http://i35.photobucket.com/albums/d153/rb26deet32/FS%20Pictures/harnesses.jpg The total for all the parts separately is $8,785. I will take off a good amount if you are interested in buying or trading everything. If you are interested call me at (614)760-8552 and leave a message. It's my home phone so I probably wont answer it. Or you can text me at (614)625-7296. Text only. I have 0 minutes on this phone. Or email me at rb26deet34@gmail(dot).com Thanks. Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 7, 2012 Author Report Share Posted September 7, 2012 Bump, everything is OBO. Also, I'm parting out, not piecing out. So no, you can't have my front wheel bearing or my left front fender. Thanks. Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 7, 2012 Author Report Share Posted September 7, 2012 Axles are gone btw. Link to comment Share on other sites More sharing options...
schmuckingham Posted September 7, 2012 Report Share Posted September 7, 2012 SC61 T4 fanged? Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 8, 2012 Author Report Share Posted September 8, 2012 SC61 T4 fanged? Yes sir. Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 11, 2012 Author Report Share Posted September 11, 2012 Also I will consider trading most of or all of what I have for a nice daily. Or a beater and a bike. Only restrictions on the trade are it needs to get decent mpg. LMK what you have Link to comment Share on other sites More sharing options...
mugen Posted September 11, 2012 Report Share Posted September 11, 2012 vouch for a great guy and legit parts Link to comment Share on other sites More sharing options...
rb26deet32 Posted September 11, 2012 Author Report Share Posted September 11, 2012 Well I decided to hold off on parting out the car. I'm not really getting any interest except for random things like inner fender liners and hatch covers... So for now I'm going to be keeping it. Link to comment Share on other sites More sharing options...
Recommended Posts