Jump to content

Who knows about Proper garage door operation?


Jsvob03

Recommended Posts

I have a two-car garage (well, two actually..score), and one of the doors has forever been a problem. forever = 1 year, just fyi.

anyhow, when lifting the door, it would sometimes get stuck or be really difficult to lift (as compared to the door next to it). So today i lubed all the moving parts. goes up WAY easier. but i still had the getting stuck problem. here is what was happening. the door itself would 'lean' to the right, causing it to hit the track. I have no idea why it would do this, but if i were to re-center it, it would roll up with no problems. here is how i fixed it. I jbwelded the steel rod that has the roller on it to the hinge. it doesnt obstruct anything, and works WAY better and never gets stuck.

is something going to fail, or am i good?

Link to comment
Share on other sites

It shouldnt be an issue if you welded the rod to the hinge. As long as it still moves it shouldnt affect anything. Can you feel it pull to the right when you raise it as well as seeing it lean to the right? If you feel it pull take a look at your springs. There should be a painted line on your springs. Count the rotations and make sure they are the same on the left and the right. You should also look to make sure that there are no cracks in the spring which can cause a lot of extra resistance too. If none of those problems exist, and its still rolling smoothly after you JBwelded it, i wouldnt worry too much about it. Hope this helps.

Link to comment
Share on other sites

it sounds to me like your need to check your spring tension like alab said. I had the same issue w/ my single. also check and make sure you lifting track is at pretty much a 90 to the motor

Link to comment
Share on other sites

The springs look fairly new (2 per door, about 1.5" diameter in length.) I just bought the house a little over a year ago, so im not quite sure as to what has been replaced, and when. the springs just appear more shiny than the rest of the stuff.

its a manual door, no motor.

as far as danger..last winter i was opening the door from the inside, and the left side roller (the one I JB'd) fell off the track. then, the right side one popped out. guess where the panel hit? my head

thanks tho.

Link to comment
Share on other sites

There shouldnt be spacing between the coils... It should be completely together. While the door is down the "spray paint" line should be strait and while the door is up both springs paint line should have the same amount of rotations. As long as they do there shouldnt be too big of an issue.

Link to comment
Share on other sites

i believe you're thinking of a different setup. the springs at my work run perpendicular to the rails, right above the door. big round ones that twist during operation.

Mine, run parallel to the tracks, and expand when the door is down, and compress when its open.

Link to comment
Share on other sites

Ok... I was thinking you had torsion springs not extension springs. That changes things a bit. My bad. Are both springs in the same position on the bracket? The cables should connect to a bracket near the curve of the track. Make sure they are both in the same hole. Also, raise the garage door up and see if there is the same amount of "slack" which shouldnt be much mind you. Ill see if i can find something for you to help you look at the springs. If it isnt the springs it may be the wheels. Do they spin freely? Dents or warps in the track? You said it sits cockeyed. Is that always or only when it sticks?

Link to comment
Share on other sites

i'll look into the spring measurement, after i replace some pulleys.

I was lookin' it over, and found 2 of the four pulleys are WASTED! like, there's only 5 rollers in the whole thing. looks like it should have around 12, so its just grinding as it rolls. added resistance explains alot.

thanks for the link. good info nonetheless.

Link to comment
Share on other sites

i'll look into the spring measurement, after i replace some pulleys.

I was lookin' it over, and found 2 of the four pulleys are WASTED! like, there's only 5 rollers in the whole thing. looks like it should have around 12, so its just grinding as it rolls. added resistance explains alot.

thanks for the link. good info nonetheless.

That would make perfect sense yes. I hope replacing those wheels works out for you.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...