RHill

Not that I know of. Thinking for peace of mind, it may all go back to Racetech.

Riding, guns, and wrenching.....you will fit right in! Welcome to OR!

been back and forth with them a few times...they have been a great help so far. I'm debating between sending the valves & rear shock in, or getting them locally serviced. It's a catch 22....send them out and I'd get the best service for sure, but no local support when it comes to tuning.

so here is an exploded view of the fork broken down. the tiny little o-ring bottom rightt (believe it is 2mm thick x 42mm ID) was chewed up on one fork and the other was completely severed.....I'd put money someone removed the cartridge previously without first removing that O-ring. It is really fun to put that little guy into the casting after the cartridge is installed, and that is the only way I could figure avoiding pinching & damaging the o-ring. Nothing a few minutes with some dental picks couldn't take care of. Tested the seal on the fork by wrapping a tie-down strap and compressing it almost fully and leaving it sit for a couple hours....nothing leaked. The bike is now back together, but I'm thinking it is going to need to come back apart AGAIN, because the compression dampening is not functioning properly. These Race-Tech cartridges separate compression and rebound damping into individual forks. The rebound fork works great, but I can turn compression fully out to fully in and it doesn't reflect (much) in the damping. The odd thing, with the cap off and manually moving the damping rod, the damping changes with pressure to the internal rod. The bike is now back together, but I'm thinking it is going to need to come back apart AGAIN, because the compression dampening is not functioning properly. These Race-Tech cartridges separate compression and rebound damping into individual forks. The rebound fork works great, but I can turn compression fully out to fully in and it doesn't reflect (much) in the damping. The odd thing, with the cap off and manually moving the damping rod(as pictured) the damping changes with pressure to the internal rod. When fully assembled, the damping adjustment does little. Bounced the bike and got like 90 mm of travel with the compression fully out and 85 with it fully in. I'd expect it to nearly hydraulically lock like every other set of forks I've bounced in the past...the rebound settings work as expected. For shits and giggles....took a couple pics of my homebrew fork fluid height gauge

Damn that is ugly!!! Hope you heal up quick!

on a more serious note.....are you talking to remove the wheel from the bike, or the tire from the wheel?

so there is an o-ring....I'll get pics later

@TimTheAzn starting next year I should be down to one for the "normal" short trips.....for the long ones, if there is space, it just makes sense to take 2 if you have them. I mean look what happened to Brandon and how well it worked out that Dan and I both had "spares".

even comes with a reel to wind it back up!

Toyhauler! (May have a vested interest seeing that you are like 10 minutes away)

you will also need 1000' of extension cord, because you are not parking that thing close....was so nice at NC and Summit with no generators running

no experience with it, but a pretty damn good price: http://www.newegg.com/Product/Product.aspx?Item=9SIA05F3GM1852&Tpk=9SIA05F3GM1852&utm_medium=Email&utm_source=IGNEFL093016&cm_mmc=EMC-IGNEFL093016-_-EMC-093016-Index-_-MECH-_-Marketplace-EB1A&et_cid=29128&et_rid=2035469&et_p1=&email64=UkVIMTU1NUBHTUFJTC5DT00

btw the pics work for you? some reason every time I try to embed them, it doesn't work, or the links break after a day

Never pulled the chrome out of the casting previously, but I've had damping rods out....this is something different. Normally there is an allen bolt running up through the bottom of the casting, and that secures the damping rod. These are an aftermarket (RaceTech) conversion of 09+ GSXR 1k big piston forks to single sided damping rods.

there's not one in my fork for sure, haven't pulled apart the stock ones yet, but I'm assuming it will be the same. Just added two photos to the album that look down into the casting. You can see an aluminum flange with spanner holes. The flange is attached to the damping tube....it is loose right now, but when the chrome is tightened down, it secures it in place.

so they are just saying re-Loctite it...hmmm maybe I'll do that and add a little silicone on there as well

where you find a parts diagram? nothing I can find has the leg/casting broken apart, just the dust and fork seal

Ran the new bike for 3 sessions over the weekend; it turns out the one fork was leaking between chrome and casting, so they came back off. (the second one had a tiny weep) The fork that was leaking has silicone (I think) on the threads of the chrome. The one that was nearly dry, didn't seem to have much of anything. Any recommendations for reassembly? Link to a few photos: https://goo.gl/photos/wkjo5Z4bwqdgsBPc7 I've heard that most forks have a seal and red loc-tite on the threads. These have no seal at the bottom and they are secured with a set screw. As the fork is screwed into the leg, it actually secures the damping rod into the casting. Without the chrome tube in place, the damping rod jiggles around free, only retained by the little spanner screw where the compression screw is normally located.....which will be removed tonight for a full inspection.

safety wire, zip ties, loc-tite, and duct tape

found a way to save money and still attend Mid-O: LOL, no peer pressure, none at all

so much POWA Speaking of trackfever, Tim, you see the Mid-O 10/3 thread? lol

Dan, I'm pretty sure it is communicable and you picked it up during the ncbike and Summit trip... Known as trackfever, most commonly occurring at the end of track season, but it's been known to insect first time track riders as well. LOL

*cough* think I'm coming down with something *cough*

Full day? 10/3 is Monday. Monday or Tuesday? Would love to make it, have to see if I can get the 1k ready in time

there was a good deal for one on facebook the last couple weeks, had to resist the temptation so I could stay a squid