ross

Ignition and Start Switch Replacement Tools Required J-42759 Ignition Switch Connector Release Tool(not required, you can use a screwdriver to push in the tabs) Removal Procedure 1.Disconnect the negative battery cable. Caution: Refer to Restraint System Service Precautions. 2.Disable the SIR system. Refer to SIR Disabling and Enabling. 3.Remove the hush and knee bolster. 4.Remove the steering column trim covers. 5.With the key installed, turn the key to the RUN position 6.Install an allen wrench into the hole on top of the lock cylinder housing. Push down on the allen wrench to release the tab on the lock cylinder inside the lock cylinder housing. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/1.gif 7.Slide the lock cylinder out of the lock cylinder housing. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/2.gif 8.Disconnect the passlock and key buzzer from the lock cylinder housing. 9.Insert J-42759 (2 small screwdrivers work just fine) into the lock cylinder housing to release the tabs on the ignition switch. 10.Pull the ignition switch out of the lock cylinder housing. 11.Disconnect the connector from the ignition switch http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/3.gif Installation Procedure Important: The gears between the ignition switch and the lock cylinder housing must be in the correct position. Failure to do so will cause a misalignment of the gears in the ignition switch and the lock cylinder housing, which may result in a NO START or BATTERY DRAIN. 1.Verify the alignment of the gear (1) in the ignition switch (2). If gear (1) is not in position shown, turn gear in ignition switch (2) until you reach the correct position. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/4.gif Important: In order to reach a stop while rotating the lock cylinder housing gear you MUST push and hold in the solenoid on the electric park lock. 2.Use a screwdriver to rotate the lock cylinder housing gear counterclockwise until it hits a stop. 3.Connect the connector to the ignition switch. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/5.gif 4.Insert the ignition switch into the lock cylinder housing. The tabs (2) on the ignition switch MUST be seated inside the lock cylinder housing (1) for proper installation. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/6.gif 5.Use a screwdriver to rotate the lock cylinder housing gear clockwise to the START position - allowing it to spring return into the RUN position. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/7.gif 6.Align the lock cylinder and install the lock cylinder into the lock cylinder housing. 7.Connect the passlock and key buzzer into the lock housing. http://i97.photobucket.com/albums/l238/branndonw/TBSSowners/8.gif 8.Install the steering column trim covers. 9.Install the hush and knee bolster. 10.Enable the SIR system. Refer to SIR Disabling and Enabling. 11.Connect the negative battery cable. Refer to post #15 for real pics if necessary. http://www.tbssowners.com/forums/showthread.php?t=50580

It's a 10 minute job to swap. I'll find the how to on tbssowners and post the link in a bit. It's a $25 part that will leave you stranded, ask me how I know.

Covers up all those Harley oil stains nicely.

Driveshaft for an Abrams tank.

I'm really digging that 2nd link to the newport show.

A used one will be full of HIV semen and fail.

What did she want you to fill her with?

Steel or plastic follower?

I have both p90x and insanity on flashdrives...maybe I should get around to using them.

Spending all those greenbacks on t-shirts and leather pony tail wraps doesn't leave much available funds for silly shit like tires.

An xbox360 slim 4gb, forza 4 limited edition, modern warfare 3, a keyport (cool ass key gadget), a 1776 Tactical "2nd Amendment" range backpack, and some other stuff.

Mom jeans

This is an awesome idea but this is honestly the first year I haven't received a single gift card.

Here's another vote for Dale at delta epsilon.

Xbox360 with kinect, modern warfare 3, forza 4 limited edition, a keyport (cool key gadget), rcbs reloading kit, cologne, under armour sweats and a sweatshirt, 1776 tacticle "second amendment" range backpack, cash money, and some other stuff. Girlfriend got a new laptop, iPad2, and a kindle touch :fuckyeah: Posted from my new iPad :gabe:

It was going south before it started.

Once again we will point out, the picture you posted is an '06-07 GSXR 600 paint scheme, 750 forks, and gsxr 1000 passenger pegs...just in case anyone missed that little tid bit of info.

Archos makes some mp3 players. http://www.archos.com/

I think I'm going for 300 blk out too. Pm sent.

Different body kit? This isn't a shitty civic we are talking about here...this is a shitty bike that started with the wrong fucking fairings and has now been repainted. If that (plus the fact he is a proven pathological liar) doesn't throw up all kinds of red flags screaming wrecked or stolen then I don't know what would. Besides the fact that it had the wrong fairings to begin with, it's been repainted. Do you know what a pretty fair assumption would be when a bike has been repainted? Bueller? Anyone? Anyone? It's probably been wrecked. It's all cool if you want to take the word of a kid you've never met before, who is a proven liar time and time again, who posts a bike for sale for a much higher price than he bragged about buying it and then lies about how much he purchased it for, but I'm just here to point out the facts and not assumptions of the character a person (Jcroz) displays.

Sorry, $4500. You're right, that is a lot more money than $4200:dumb: And that pic was posted in one of the other threads you started that went to fuck and back.

Wait, is this the same stolen/wrecked/etc bike (that you were bragging about getting for $4200 and are now trying to sell for $6000) we are talking about here?

Coupon code is expired already.

THAT SHIT's BEEN WRECKED!

Why are you crying about rep? No one gives a fuck.