TurboRust

are you sure its not 1.5? i just typed filler neck hose on napas site and got these numbers for 1.5 http://partimages.genpt.com/thumbs/305437.jpgGas Filler Neck Hose, 1.5" Product Line: http://partimages.genpt.com/partimages/1130291.gif NAPA Belts & Hoses Select To Compare NBH 1030 http://partimages.genpt.com/thumbs/520377.jpgGas Filler Neck Hose, 1.5" Product Line: http://partimages.genpt.com/partimages/1130291.gif NAPA Belts & Hoses Select To Compare NBH 1031 http://partimages.genpt.com/thumbs/520378.jpgGas Filler Neck Hose, 1.5" Product Line: http://partimages.genpt.com/partimages/1130291.gif NAPA Belts & Hoses Select To Compare

Call dave at oreillys in Westerville I almost positive you can get on goodyear's website and they list a part number for it...im on my phone or is get it for you

tim what was that ? is it photoshopped?

motor is almost done, going back in shortly

lets see if any can break a world record and run a low 13.... contour/mystique/cougars should only be road/roll/ raced

double check for leaks, sounds like air is entering the system... turn the wheel all the way to the right against the lock and turn the car off, let it sit for 15 minutes.. this should remove all air from the system. unless there is a reoccurring leak

the problem is that you're wanting to put a smaller then o.e. wheel on it and atleast for someone like us(who dont stock alot of rims) we could have $100 bux in shipipng something in for it to not fit.. if you have some wheels you know will fit, i'll gladly help, but otherwise we're literally guessing... anywhere from a 42-52mm+ offset should work fine, the higher the better.

yeah the boat is a 1/2 mi from alum, so i'm going to meet him there, look it over and then head out on the water with it.. everything goes kosher, take it by said mechanic for an inspection.

Its a fish&ski stratos bass boat with a 90hp johnson outboard. i think i found a mechanic to take it by up in delaware where the boat is at.

should i have it checked at a boat mechanic or meet him on the water and if it runs god dont worry about it.?

Thanks for coming in, but as one more measure of our shop being well rounded, i'm off today, andy, sadly is at a friend's funeral, but matt my service manager is a great guy, and Cody is my normal alignment guy (Andy and I do the specialty stuff normally) Anytime you need something, even if its my day off, do not be afraid to call 232-8881

oh and all of this i've seen under 50k

dont do it tie rods ball joints struts shocks brake eaters intermediate shaft money pits

Berto's a solid guy, fuck off vultures... hope you get er fixed Paul.

mseebs i pm'd ya

http://www.columbusracing.com/forums/picture.php?albumid=585&pictureid=5245 This was one of the bigger ones, good ratio picture here the dude holding it was a good 240 or so

Dave at Cross eyes charter out of lorain area just west of cleveland.

It must be the angle of the shot, there were 4 in there over 30" the smallest fish was about 21" and 3.5 lbs

It was a charter boat with my dad,cousin, his wife and 2 friends... Kept us busy all day, had a good 13-15 lb steelhead on and it got off right at the boat, bunch of sheephead and white perch

went out on erie today and absolutely killed the walleyes.. 26 fish from 3.5 to a lil over 9..most were 6+ heres a couple of carnage pics first one is all 26.. http://www.columbusracing.com/forums/picture.php?albumid=585&pictureid=5243 next is the 20 that were over 6lbs http://www.columbusracing.com/forums/picture.php?albumid=585&pictureid=5244

factory pirelli rubber not so sticky

I heart your transmission..

This car is tits... until you're adjusting rear alignment... tru story

lt1-235hp-155mph- electronically limited lt1 with slp package-300hp-155mph-electronically limited

explorers have a 31 spline limited slip in them.