Jump to content

Small Engine Issues - Chainsaw


max power

Recommended Posts

I have an old McCullouch Timber Bear. It has always run well until recently. It has become a bitch to start.

I have to pull the plug and dry it every time. Then usually hit it with starting fluid.

Once it's running, it runs fine and strong, idles well and all, but if you shut it off, it won't start again.

I pulled the plug and cleaned it. It was wet with gas, but it didn't spray out of the plug hole when I cranked it sans plug.

I pulled the carb and checked it. Clean and unclogged. The fuel line is new, full of fuel and its getting good spark.

Not sure what to make of it. Thoughts?

Link to comment
Share on other sites

Most likely needs the Carb rebuilt. There is a small checkvalve that prevents fuel from leaking past the Carb when the engine is off. It's most likely leaking and flooding the engine when turned off. Does the primer bulb go dry when the engine is off? That is usually the easiest external sign of the internal leak.

  • Upvote 1
Link to comment
Share on other sites

Low compression, or possibly sucking air (crank case seal or intake boot). Leaning more towards low comp. Do you use quality mix and fuel? Ethanol is hard on small engines. May have been running lean due to crud in carburetor or plugged fuel filter. How often do you change the fuel filter?

Link to comment
Share on other sites

No bulb, no fuel filter. Old skool! Early 90's model.

I did the finger-in-the-hole compression test and it seems to have good compression. Rebuilt the carb 3 years ago and have maybe 3 or 4 hours on it since. Not that that means anything.

Link to comment
Share on other sites

Most likely needs the Carb rebuilt. There is a small checkvalve that prevents fuel from leaking past the Carb when the engine is off. It's most likely leaking and flooding the engine when turned off. Does the primer bulb go dry when the engine is off? That is usually the easiest external sign of the internal leak.

This also. Check fuel line. My '97 husky had a cracked fuel line where it exits the tank once.

Link to comment
Share on other sites

No bulb, no fuel filter. Old skool! Early 90's model.

I did the finger-in-the-hole compression test and it seems to have good compression. Rebuilt the carb 3 years ago and have maybe 3 or 4 hours on it since. Not that that means anything.

Junk fuel. Gasoline goes to shit in a hurry nowadays. If a carburetor isn't too expensive, i'd toss one on it. Engine should have at least 100psi comp.

Link to comment
Share on other sites

Just tried the spark test again and it doesn't appear I'm getting good spark. Hopefully it's just the plug, but that doesn't make sense to me since it runs and idles fine once it starts.

Coil could have been slowly dying. Especially if it is worse? when the saw is hot. Sparkplug cheapest place to start. For the love of Odin, put a filter on it! Mower or saw shop should have a buzzbox to test coil.

Link to comment
Share on other sites

Rebuilt the carb 3 years ago and have maybe 3 or 4 hours on it since. Not that that means anything.

 

Hate to say this, but I'd tear it apart and re-check your work.  Also, give a good look at the intake valve...  out loud I'm thinking "saw gets hot, intake valve sticks, allows too much fuel in and floods the plug when you try to restart.  Taking the plug out and drying allows engine time to cool down and valve stops sticking."

 

Just a thought.  Thank goodness it's not a Pull-on...

Link to comment
Share on other sites

Hate to say this, but I'd tear it apart and re-check your work.  Also, give a good look at the intake valve...  out loud I'm thinking "saw gets hot, intake valve sticks, allows too much fuel in and floods the plug when you try to restart.  Taking the plug out and drying allows engine time to cool down and valve stops sticking."

 

Just a thought.  Thank goodness it's not a Pull-on...

 

The carb is pretty easy to disassemble at this point.  Ill give it a check tomorrow.  I think my issue is more to do with weak spark, though Ive been wrong before, hence this thread.

 

If I hadnt just invested in a new Stihl weedeater, Id craigslist this old beast and get a new Stihl saw.

Link to comment
Share on other sites

give a good look at the intake valve...  out loud I'm thinking "saw gets hot, intake valve sticks, allows too much fuel in and floods the plug when you try to restart.  Taking the plug out and drying allows engine time to cool down and valve stops sticking."

 

 

Huh? :crazy:   Intake valve?  This is a 90's chain saw, there is no 4-stroke here.  Better fix that to be a reed valve.  :lolhitsign:

Link to comment
Share on other sites

Grab the handle of the pull cord and pull it until its all the way extended.  Once out all the way, use your other hand to make sure you have a firm grip on the handle. Next violently swing it around in a circle above your head. When your at maximum speed release it off a bridge. On its way down yell " Fuck you , you piece of shit!". Get back in you car and go buy a new one.  

 

I did something similar to that with my pressure washer wand over the weekend but shucked it into the trees out of anger.. Seems that everytime i let someone borrow it, it comes back broke. Going on wand number 3 now. It shall never be loaned out again.

Link to comment
Share on other sites

If i were to put it on the replacement list, it would sit firmly behind the compressor that is dying a slow death and the gas grill that is rusting out and the repair on the wife's truck that is pumping oil into the air cleaner all of a sudden.

In other words, it's a good old saw that just needs repaired, and quick. I gots free firewood to go collect.

Link to comment
Share on other sites

Huh? :crazy:   Intake valve?  This is a 90's chain saw, there is no 4-stroke here.  Better fix that to be a reed valve.  :lolhitsign:

Lol. No Shit, Need To Read Before I Hit Post. Shouldn't Get On Here WhenI 've Been Hitting The Jamesons

Link to comment
Share on other sites

Well....I looked up the plug gap, found it to be a little narrow, and re-gapped.

IT LIVES!!!

Hopefully that was all it is, but we shall see. It definitely runs at higher RPMs now as opposed to yesterday. I don't fully trust it yet as it ran before, but it does start after being run now and is t nearly as hard to start.

Link to comment
Share on other sites

Grab the handle of the pull cord and pull it until its all the way extended. Once out all the way, use your other hand to make sure you have a firm grip on the handle. Next violently swing it around in a circle above your head. When your at maximum speed release it off a bridge. On its way down yell " Fuck you , you piece of shit!". Get back in you car and go buy a new one.

I did something similar to that with my pressure washer wand over the weekend but shucked it into the trees out of anger.. Seems that everytime i let someone borrow it, it comes back broke. Going on wand number 3 now. It shall never be loaned out again.

I know how that goes, all too well!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...