Brandon

Well good luck ray! ARP makes lunatis bolts Those rods are tuff rods though, surprising.

Nice runs boss! Regards

Did the rod cap let go? Seems like the one rod the cap/bolt let loose on the one rod, what I beam rods are those? ARP 2200 bolts? Sorry to hear Ray If you need anything we are around to help! Regards

Looks good Matt!

I am hoping for the LSA engine combination, we already have a lot of r&d with that in the new CTSV, and they are wonderfully built, with great power potential. I like it, and from a pretty good source my hunch is its in the logistic phase of being built! Regards

Same day or Next day almost always. Regards

We can tig weld if you need something quickly

Use either Wheel Medic, or StreetWerkz on Clare Ave.

Cool I will hold them, I also have some stainless braided lines ill kick in. -Brandon

I have switched gears since acquiring a home, and having a new motor for my car, I do not need these parts I have had on the shelf for a year. I need to sell relatively quickly. I will meet or ship parts anywhere at my expense as well. AEM EMS for the S13 Redtop motor, NEW used only in mock up, never tuned the new engine on this. $850 OBO (part number 30-1601) http://farm4.static.flickr.com/3486/3938086079_a68a265778_m.jpg http://farm3.static.flickr.com/2642/3938864838_4178affa8e_m.jpg Tial 38mm wastgate, with NEW Stainless valve and seat, good condition, 1 bar spring. $100 OBO http://farm3.static.flickr.com/2602/3938868072_f799e6422f_m.jpg http://farm3.static.flickr.com/2440/3938089537_5a025c0c38_m.jpg Greddy SR20 head studs (by far best on the market used by record setting Mazwork S14) These are 280 new, Ill take $200 OBO, these are NEW never used. http://farm3.static.flickr.com/2432/3938853486_6ef6172355_m.jpg Cosworth multilayer head gasket 1.1mm NEW never used $90 OBO http://farm4.static.flickr.com/3440/3938850354_98b8657359_m.jpg http://farm3.static.flickr.com/2438/3938851932_bbe9fbb487_m.jpg Peak Boost T3 Ram horn style full tig welded exhaust manifold, sandblasted and ceramic coated with 2300 degree coating, which is why its Black. 38mm Tial Flange, this is a real exhaust manifold not a cheapy ebay, will not crack. $750 (with coating I have 1400 in it) http://farm4.static.flickr.com/3461/3938856962_0e9b2587e8_m.jpg http://farm3.static.flickr.com/2515/3938861646_0a81577419_m.jpg http://farm3.static.flickr.com/2629/3938083125_1fccae37fd_m.jpg http://farm3.static.flickr.com/2622/3938081531_34aaa2c104_m.jpg R33 Used Front calipers, will bolt up to S14 I can source calipers for cheap as well, under 60 dollars. I would like to get $60 for these calipers! http://farm4.static.flickr.com/3463/3938869770_8259952479_m.jpg Thanks for checking out these items Regards

Nissan is a know specialty at our facility, ask Tank (our fabricator) anything about your sentra he has the answer, its awesome. We just recently did another emanage car with a hot shot kit on his 2.5. Turned out very well. We can touch up his tune, for optimum driveability and power out put, out emphasis is on how the car drives and starts up, cold and hot, versus just a few wide open pulls other facilitys use only for calibartions. Regards

We sell Katechs short shifter then the bushing set up, it is night and day! -Brandon

It would cost more then 24k to do that car like that. I would buy that one after a good inspection. Regards

Part of the diff issue is the design, and then the front bushing the diff, which holds the pinon angle. This bushing is garbage, and causes the pinion angle to change often under wheel hop or acceleration. BMR makes the following that I would buy if your going to get one http://www.bmrfabrication.com/CTS-V/PS001installed.jpg Right from BMR " The differential is mounted to the rear cradle by soft rubber bushings. There are two bushings in the rear and only one in the front. This front bushing is responsible for maintaining pinion angle which is critical for u-joint life, launch consistency, and overall driveline efficiency. By simply releasing the clutch at idle with the brake on, the stock, unsupported pinion measures up to 2 degrees of deflection. Aggressive driving loads this bushing significantly more allowing up to 4 degrees of pinion deflection before the OE bushing "bottoms out". Our Pinion Support adds a low deflection polyurethane bushing to the front mount and reduces deflection to almost zero off idle. The result is immediately noticeable as it removes the "spongy" feel noticeable off idle and decreases the audible "thunk" heard when the OE bushing bottoms out." Then add the anti wheep hop kit for insurance Regards

PTE 6567 billets If you like Brian you can give me a call Regards Brandon

We did an LS1 coil conversion on the Lt1 car we had here, it wasn't all that bad, but its a few grand for certain.

We have done some work on that car for Dave , been here a bunch. Its a nice car. -Brandon

Give me a call and or stop down to the shop, I think our 10k+ sq ft facility and our knowledge will speak for itself, base what you do to this car, on your knowledge and your experiences, not what *hear say* you have heard, this is specific to any shop. Good luck -Brandon

We are stuck with a 3.42 gear ratio

Larry, We talked on the phone earlier, (good to hear from you again)I know the car now, and I can give you the information on it. He is a member on this forum. Give me a call back when you get more free time, and I can give you specifics. And Cordell...That car was completed in 2006, to client specs, switches, and placement. That car does run real strong ( I mean 10s are good.. ), and it has been since 2006, sticker and all Regards -Brandon

Cant wait to see Mark get this down the track now! Here is a link to some videos of the old set up, and more information! http://www.ipsmotorsports.net/article_info.php?articles_id=12 Regards -Brandon & Team IPS

We have 3 welding machines, and plenty of fab materials. We can tig you SS" if you need, just contact us at the shop. 614-444-5884 Regards -Brandon

We work on both platforms regularly. We can complete this service while you wait in our show room, with complimentary beverages and snacks! I sent you a private message with a labor quote, hopefully we can help you out. Regards -Brandon

Give us a call , 614-444-5884 we have a solution for you Regards -Brandon

The pictures are hiding Use the link i posted it contains the flickr photos.