Jump to content

Front end vibration


jd724

Recommended Posts

OK here goes.  Ill try and keep it as short as I can. I've had this vibe problem all season so far. I don't think it started last season but I can't remember. I had a new cheap tire put on the front. First thing I did was replace the tires with a new set of q3's. Vibe improved very very slightly maybe. It goes from low to high frequency the faster I go. Rode the bike at higher rpm's in lower gears and the vibe didn't seem to increase at higher rpms. So I'm thinking it's speed related. It all seems to be in the wheel and the bars. Also felt a weird vibe every so often when I weave the bike back and forth in the lane. I was around 70mph. No clcking or noise. Just the vibe. I bounced it off Isaac'sPoppa and he mentioned wheel bearings right away. That's what I was starting to think but I wanted the opinion of a pro. The bike only has 8k on it. I did find some posts on other forums about front wheel bearings on Z's going bad around 8k.Just a few but the 8k is what got me.  Various reasons. One was a seal went bad and moisture got in. Another one was faulty installation so they said. But regardless the vibes they had were resolved when the bearings were replaced.

 

So I'm gonna give it a shot myself. I'm hoping I see a mess in there when I get the hub open. Doesn't look too tough. Gotta be sure I put good grease where it needs to be, get my torque to specs, don't beat anything up getting the old ones out and the new ones in and get everything back on exactly as it came off. I will probably take my rotors off as a safeguard. Question: OEM bearings are around $60. Allballs kit is $20.  Why?  I've read that Allballs are better than any oem. Yeah I know ceramics would be the best but I can't afford em right now. Also I'm not sure if that's the problem. If I have a hub or axle problem, I don't want to put $300 bearings in there. Watcha think?

Link to comment
Share on other sites

Bearing.

It may not look a mess, but after wheel is off spin each bearing by hand and feel for notchyness or inner race movement.

Have you ever used a power washer to clean the bike? This can force moister in places it would not normally go.

Link to comment
Share on other sites

I thought about steering head bearings but at only 8k?  I'm thinking about getting the TB's sync and engine balancers checked sometime as well. If either is off it will cause a vibe but that's out of my league.

Link to comment
Share on other sites

From what I can tell.....   Z's are packed tighter than a...(use your imagination)   Even the battery is packed up under the front half of the bike.  Tank has to come off for pretty much everything.    I'm gonna take one thing at a time. Goin over everything in the wheel/brakes first. Then steering head.  Hopefully it will be resolved by then.

Link to comment
Share on other sites

Thanks guys!   Dustin, you're talking about the steering head nut right?  Thanks Isaac's Papa!  I may take you up on that.  I start a week of working nights this Friday.  I may stop by your shop during the day if that's ok. Ordering parts today. I'm gonna try the allballs. I've read nothing but good about them and at half the price of OEM I'll try them first. Just have to make sure they come with seals and everything I'm gonna need.  I'll probably be replacing them with ceramics within the next year anyway. I'll check their kit again and make sure they come with everything I need. Ordering a new front stand as well. I eventually wanna try the Ohio Mile. Probably won't happen this year. Bike probably won't be ready and I need a suit. 

Link to comment
Share on other sites

Jd, yes Dustin is referring to steering head. Kawasaki is notorious for them going out. The 250s and 300s typically need replaced in the first few years. I have read the same about all the ZXs.

Link to comment
Share on other sites

Here is the exploded view. I'm not speaking of the steering head nut. If you remove the top triple you'll see nuts under there. One tighens the other is a locking nut.  If you back the locking nut off and then get a spanner and follow the procedure in the service manual to retorque the steering head it may fix the problem. The steering head is tapered roller bearings and they can sometimes have an undectable amount of play that can create a front end vibration. I've had it happen in my zx-6 and on a concourse 14 before as well. I'm suspect of it on my zx1000 right now too.

 

in the exploded view it is part # 92210 and 92210A. It's important to follow the instructions in the service manual though, the torque specs are pretty important and you're going to want to be sure the steering isn't to tight after adjustment.

 

Try to make one change at a time. So you can narrow down the issue and then if it happens again, you'll know what to check.

post-9151-0-56248200-1398624583_thumb.jp

Link to comment
Share on other sites

Thanks guys. I'll try the wheel bearings first. I do believe my steering has loosened up some but it looks like it might be a bit out of my league but we'll see.  Thanks again guys!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...