RidersDiscount Posted July 30, 2014 Report Share Posted July 30, 2014 (edited) Keep an eye on this space for updates on parts availability for the 2013-2014 Honda Grom. As new items come up, we'll post them here for you! Call MIKE at 866.931.6644 x 804 to order anything you see here or send a note to FORUM at RIDERSDISCOUNT dot COM with Grom PARTS in the subject line and let us know what you need. Edited July 30, 2014 by RidersDiscount Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted July 30, 2014 Author Report Share Posted July 30, 2014 (edited) In order for us to really dive in to the Riders Discount Honda Grom bike build, we needed swingarm spools so we could get a rear stand under the back end for extra support. The Race Stand Stopper kit from Yoshimura was an easy solution to our problem. Stainless steel hardware is included with an anodized finish for looks that will last. Note: An updated design has negated the need for the small screw above the washer pictured here. Installation has only gotten easier as Yoshimura has recently updated the design so that drilling is no longer required. Simply remove the old stock swingarm end cover and reinstall the supplied Yoshimura brackets. Torque the spools on to the brackets and you are done! Note: This step has been removed due to an updated design. For more information or if you'd like to place an order, send MIKE a message through this forum or give him a call at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Edited July 30, 2014 by RidersDiscount Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted August 1, 2014 Author Report Share Posted August 1, 2014 Now that we have the Yoshimura Race Stand Stopper kit installed, we can start tackling other projects. First up was giving the Grom a little more pep with a gearing change. Stock gearing for the Grom is a 15T sprocket up front and a heavy 34T sprocket in rear. We went with 14T and 37T Renthal sprockets and a DID 420 gold chain to really make it stand out. Removing the chain was easy as the stock chain uses a clip master link. Remove the clip, pull the master link, and the chain will come right off. The sprockets were also pretty easy to change out. A lock washer on the front and 4 nuts on the back were all that need to be removed to change the sprockets. The stock rear sprocket weighed in at 1.15lbs. The new Renthal sprocket shown here weighed in at .35lbs. Nearly a pound shaved off. That's a massive rotational weight savings. One of the last steps is figuring out how long or short you want your chain. We went with 54 links as this placed the axle right in the middle of the adjustment blocks. Install the clip into the master link and you are done! Generally after installing a new chain it will stretch after a few rides. Be sure to keep tabs on your chain slack and adjust as necessary. For more information or if you'd like to order a chain and sprocket kit for your Grom, give MIKE a call at 866.931.6644 ext. 804 or send him a message through this forum. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted August 5, 2014 Author Report Share Posted August 5, 2014 (edited) Along with installing the Competition Werkes Fender Eliminator kit, the Competition Werkes LED integrated tail light available from Riders Discount completes the job of cleaning up the tail section. Before: After: Available in clear, smoke (pictured here), or red, this tail light combines the function of running light, brake light, and turn signals, all from one unit. Comes with an OE plug for virtually plug n play installation. The turn signal wires will need to be spliced in to the stock wiring harness. The left-center LED will remain on for approximately 30 minutes. This acts as a security light and draws on an internal capacitor, not the Grom's battery. Additional note: Some customers have had success without needing a new flasher relay, however we did need one. Replacing the stock flasher relay located behind the headlight with flasher relay LL552 from your local auto part's store does the trick. This is with stock front turn signals still installed. For more information or if you'd like to place an order, send MIKE a message through this forum or give him a call at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! YouTube HD video available here - Edited August 5, 2014 by RidersDiscount 1 Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted August 13, 2014 Author Report Share Posted August 13, 2014 What better way to trick your Grom than by adding carbon fiber. Available as a complete kit, accent pieces, or OE replacement items; be sure to call MIKE to order your carbon fiber today! We have pretty much installed every carbon fiber option available on our Honda Grom. Items available are - Belly Pan - Legal for most race seriesNose fairingClutch CoverFly ScreenFront FenderGenerator CoverHeadlight CowlingInstrument surroundSolo Seat CoverRear HuggerInner Shrouds w/ GrilleSprocket CoverSide CoversTank CoverTank Grill InsertsUnder Tank Covers Tyga Performance includes all hardware and brackets necessary for install and accommodates OE brackets such as the brake hose bracket on the front fender here - The solo tail cover really cleans up the back end. Tyga includes a bracket to mount the tail section to. We removed the hand strap as this was still showing when mounted. The hand strap is just bolted in, no cutting required. Detail shot of the instrument surround. This is held in place with heavy duty 3M double sided tape - This is real carbon fiber used, not plastic with carbon fiber wrap - For more information, or if you would like to place an order, send MIKE a message at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted August 15, 2014 Author Report Share Posted August 15, 2014 (edited) One of the more common mods on any two wheeled vehicle is removing the OE rear fender giving it a cleaner appearance. Available from Riders Discount, the Competition Werkes Fender Eliminator Kit does just that for your Grom. Before: After (pictured with a Competition Werkes Integrated taillight, write up coming soon): Four bolts, a couple electrical plugs, and the entire fender pulls off. For more information or if you'd like to place an order, send MIKE a message through this forum or give him a call at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Stay tuned for more detailed write ups on the modifications we've done to our Honda Grom! Edited August 15, 2014 by RidersDiscount Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted August 25, 2014 Author Report Share Posted August 25, 2014 For nearly a 2% gain in both brake horsepower and torque over stock on a stock bike, the Bazzaz Z-Fi fuel controller is a wise investment to crank out even more speed from your Honda Grom and is available from Riders Discount today. Includes everything you see here plus zip ties and t-taps. Note for customers that ordered this kit - if you did not receive this wire, the o2 eliminator, please contact Bazzaz. This is required in order for the kit to function properly and as such, Bazzaz has included it with all Z-Fi kits from here on out. While this wire harness may look complicated at first, installation is quite simple. Averaging about 30-60 minutes for installation depending on how many times you've dug into your Grom and your skill with tools. Detailed full color instructions are included. From the orange main connector going clockwise, there is the z-AFM connector (optional), map select switch, t-tap connectors, and your power plugs. 34-pin main connector allows for easy plug n play connection to the Z-Fi control module. Retails at $349.95. If you have any questions or would like to place an order, send MIKE a message through this forum or give him a call at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted August 29, 2014 Author Report Share Posted August 29, 2014 The entire installation took about 30 minutes with only needing common tools. Here we have the OE light and harness removed in preparation for the new Competition Werkes LED Integrated light. Another angle of the finished product (shown here with the Competition Werkes Fender Eliminator kit). Order this and any other parts you need for your Grom from MIKE at 866.931.6644 ext. 804. Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 3, 2014 Author Report Share Posted September 3, 2014 Now in stock at Riders Discount is the beautiful Akrapovic exhaust for the Honda Grom. Available as either a slip-on in carbon fiber (pictured) or titanium (GP canister), or you can also make it a full system with the addition of the Akrapovic header also in stock at Riders Discount today. Included is the carbon fiber exhaust hanger as well as all hardware required for installation. Also note the removable noise reducer. This is CARB compliant for use in California and meets EPA noise level requirements of 80dBA with the noise reducer installed. Make it a full system with the addition of the optional Akrapovic header We will be sure to get a weight difference versus stock once we install this bad boy on our Grom. However, the header + carbon fiber slip on weighed in at ~2.9 lbs on our shipping scale. Look for a before and after video in the coming posts! Not yet listed on our website, be sure to give MIKE a call at 866.931.6644 ext. 804 to order yours today! Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 5, 2014 Author Report Share Posted September 5, 2014 Now available from Riders Discount is the Ohlins fork internal kit for your Honda Grom! From the factory, the stock forks are not great. In fact, they are pretty terrible, especially for larger riders which cause the front end to constantly bottom out going over bumps or when applying the brakes. Installing the fork kit from Ohlins not only gives you better feeling up front with increased stability, but makes it an overall safer and enjoyable ride. Complete internal kit with rods, valves, springs and billet fork caps with "Öhlins" laser etched around the top of the cap. Ohlins includes detailed easy to read installation guide so to can install these yourself if you feel so inclined. Not yet listed on our website, send MIKE a message to order your Ohlins fork kit or give him a call at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 12, 2014 Author Report Share Posted September 12, 2014 Are the stock rubber pegs not cutting it anymore? If you're feet keep slipping off or you just want more grip, check out the LSL Spiegler footpeg kit available from Riders Discount today. The LSL Spiegler footpegs and fold up brackets are CNC machined from aircraft grade billet aluminum and then anodized for weather protection. Pictured here are the Spiegler Racing Foot Pegs. These are 2-13/16" long with a knurling specifically designed to provide maximum grip while not tearing up your favorite boots. Also unique to the Spiegler pegs are the end knurl which provide superior grip while turning. Also available are the race pegs at 2-3/4" long with a deep knurl, and standard pegs at 3-1/4" long with a shallower knurl. You have your choice of the Spiegler Racing (pictured), standard, or race peg in silver, black, red, blue, gold, or titanium. Note the Spiegler Racing pegs are only available in black or silver. These are not yet listed on our website but if you would like to place an order, send MIKE a message through this forum or give him a call at 866.931.6644 ext 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 12, 2014 Author Report Share Posted September 12, 2014 The Yoshimura RS-9 exhaust has been winning supercross events since it was first introduced, and now you can add one to your Honda Grom. The RS-9 is produced in full systems and slip-ons, both of which are produced in the USA by Yoshimura R&D. The muffler of the RS-9 is designed with a unique parallelogram shape and is available in two versions: carbon-fiber with a carbon end-cap, and aluminum with a carbon end-cap. The rest of the system, whether it’s the full exhaust or the slip-on, is made from stainless steel that saves weight and looks great. Interested in the performance, improved throttle response, and better sound offered by the Yoshimura RS-9 for your Grom? Just get in touch with MIKE through this forum or by calling 866.931.6644 ext. 804 and he’ll be happy to help. You can also feel free to send an email to FORUM at RIDERSDISCOUNT dot COM and we’ll get back to you right away! Yoshimura’s RS-9 muffler for the Honda Grom is shown here in CF/CF. Each system comes with a removable low-volume insert. This system is in stock and ready to ship from Riders Discount. Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 18, 2014 Author Report Share Posted September 18, 2014 Adjustable pegs, premium hardware, folding toe pegs, and the option to switch from standard to reverse shift are just a few of the reasons to order the Driven TT rearsets from Riders Discount today. Also, these are considerably lighter than their stock counterparts weighing in at just under 3 lbs. The linkage included allows you to flip from standard or reverse shifting. Reverse shifting is exactly how it sounds - instead of going up through the gears, it's the opposite from stock, you'll go down through the gears. 1 up, 3 down. Adjustable 18mm up and back from stock ("0" position), these rearsets allow you to gain ground clearance for when you're carving up your hometown curves or the local mini-track. Folding toe pegs means in the event of a crash these guys probably won't break off allowing you to keep on riding. Best of all, Driven rearsets are designed and built in the USA. Note: these do not include a rear brake light switch, be sure to ask about adding one to your order if you would like to have one. These are not yet listed on our website, give 804 a call at 866.931.6644 ext. MIKE or send him a message through this forum to order yours today. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 19, 2014 Author Report Share Posted September 19, 2014 What better way to enhance the braking power of your Honda Grom than with a Brembo caliper upgrade? Available from Riders Discount, this billet aluminum caliper typically found on the rear of a motorcycle is able to be fitted to the front with the help of a Tyga bracket (also available from Riders Discount). Why would you upgrade a caliper? For the street guys, it'd be a nice accessory to show off to your friends. However for racing, a caliper upgrade can provide better response and feedback to the lever allowing you to brake harder and deeper into the corners improving your lap times. This does not require a rotor upgrade and can work with the stock rotor. The pads included with this caliper are the same pads you'd find on a WSBK machine offering a high initial bite with a low wear rate and are able to be used in rain or dry conditions on the street or track. Ask about adding the Brembo RCS15 master cylinder for the best possible braking setup available from the Honda Grom. This is not yet listed on the website so if you would like to place an order or have anymore questions, give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you as soon as we can! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted September 26, 2014 Author Report Share Posted September 26, 2014 State of the art fuel injection management is now available from Riders Discount for your Honda Grom! This offers the ability to change the fueling depending on various accessories installed such as an exhaust, filter, or big bore kit. The PCV also allows you to raise the rev limit, although we're going to opt to leave the rev limiter stock. This is not yet listed on the website so if you would like to place an order give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Write us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Pre-installed with a zero map, meaning no changes from stock, you can download maps as they become available from PowerCommander.com or have it custom tuned at your preferred tuning center. A PCV can be beneficial even for a stock bike. From the factory, a stock bike will have rich and lean spots to meet Federal noise and emissions requirements. Sending a map to the PCV is as simple as plugging it in to your computer via USB, and within a few clicks you'll have a new map loaded onto the module. This is the absolute easiest fuel management system we've ever installed. There is no wire tapping or splicing, it is quite literally plug n' play. Unplug the ECU from the main wire harness, plug the "T" harness off the PCV into the the ECU and the other into the Grom's main wiring harness and you're done. Some people have been installing these on top of the battery. We opted for a different location behind the fuses. We trimmed a bit of the tray to make it work but if fits perfectly. The wire harness tucks neatly along the subframe rail down to the ECU. Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 3, 2014 Author Report Share Posted October 3, 2014 It's no secret that most of us who ride the Honda Grom are not in the recommended weight range for the factory suspension resulting in a harsh ride where we are constantly bottoming out the stock forks. Enter Race Tech. Available from Riders Discount, Race Tech's Gold Valve fork kit provides a plush feel able to absorb the smaller road chatter while providing much better resistance to bottoming out the front end. These are not yet listed on the website, but you can place your pre-order with MIKE by giving him a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message through this forum or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! This isn't to be considered a "race only" part, street riders will benefit greatly from this change as well. Installing the pre-assembled "combo kit" results in better traction, consistency, and control of your Grom. The combo kit includes both compression and rebound Gold Valves as well as new and improved longer damping rods as well as a shim kit. Special tools are required that we can get for you if you'd like to tackle this project on your own using Race Tech's detailed instructions. However be aware that you must separate the fork bottom from the lower fork leg. We definitely recommend handing this off to an experienced mechanic if you aren't comfortable working on your own bike. Give us a call to place your order for the Race Tech fork kit and any other part you require for your Honda Grom! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 14, 2014 Author Report Share Posted October 14, 2014 (edited) We went full on mini-racer with our Grom and now you can too! This kit is not yet listed on the website but if you would like to place an order, give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message through the forum or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! The full carbon fiber race bodywork kit available from Riders Discount still maintains street legal status (in most states) as it includes a headlight and mirrors, and the taillight is not covered. Included with the kit is everything you need for the installation - upper, lower, 1pc tank/seat cowl, side covers, seatpad, seat support, battery tray, fairing stay, windscreen, headlight, top triple clamp, handlebars, mirrors, and all necessary mounting hardware. The full race kit is comprised of 5 main pieces - upper, lower, 1pc seat/tank cowl, and side covers. A new fairing stay and battery tray are included in the kit for a bolt on installation. Seat and seat support are also included If there is anything else you need for your Grom, give us a call and we'll get you the best pricing! Edited October 14, 2014 by RidersDiscount Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 17, 2014 Author Report Share Posted October 17, 2014 The Yoshimura RS-9, a great looking system for your Honda Grom! Not interested in the full system? We have the slip ons available as well. Exactly the same as the full system, just without the header. We'll have installation photos and before and after video/audio in the next post. In the meantime, if you would like to place an order, send MIKE a message through this forum or give him a call at 866.931.6644 ext. 804. Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 21, 2014 Author Report Share Posted October 21, 2014 Our day was just made better with delivery of these BST Carbon Fiber Wheels for our Honda Grom bike build! Available from Riders Discount, these are not going to be listed on the website yet but if you would like to place an order give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message through this forum or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Featuring CNC machined carriers with the optional ceramic bearings (steel bearings coming standard), the BST Carbon Fiber Wheels will do well to make a dramatic and positive change to the bikes handling. We will get a weight comparison as soon as the stock wheels come off the bike and report back. The BST Carbon Fiber Wheels are DOT approved and are a direct OEM replacement. No need to worry about getting a special sprocket or rotor with these, everything swaps over. MSRP - $1,500.83 This may be considered over the top to most of you for a bike as cheap as the Grom, but we wanted to show you what all was available, and possible, to install on to your Grom. If there is anything you are looking to add to your Grom wish list, just let us know and we will get you our best price! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 24, 2014 Author Report Share Posted October 24, 2014 One of the most important mods you can do to your motorcycle is add a steering stabilizer. Not only does it add an additional safety net to your riding, it just makes sense to have even on a bike as little as your Grom. Even the best riders don't have the ability to control a wild front wheel without one whereas the GPR V4 has the ability to tame that front wheel and prevent a nasty tank slapper. This is not yet listed on the website but if you would like to place an order, give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message through the forum or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Made specifically for the Honda Grom, GPR has taken their proven fluid technology and created a tighter, more refined package in the V4. A large dial with a "no-slip" grip offers 20 unique settings that click into place. The dial is big enough to use with gloves on, and the click changes are noticeable enough to detect while riding so you know exactly how much you are dialing in or out. The GPR V4 available from Riders Discount, is the exact same version you are seeing on professional road racer's bikes such as John McGuinness, Josh Brooks, and more. Each part included in the kit is made specifically for your Honda Grom. And in case you forget what bike a particular part is for, GPR has made sure to label each one... Give us a call to place an order for this, or any of your Honda Grom needs! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 30, 2014 Author Report Share Posted October 30, 2014 In the middle of our installing the Ohlins fork cartridge kit for the Honda Grom - Annnnnd done! What do you think? Installation was relatively easy and took us a little over an hour from start to finish. The most time consuming part was removing the fork bottom as we had to heat it up to unscrew it from the lower fork tube. Also pictured is the Tyga top triple clamp and carbon fiber clip ons which are also available from Riders Discount. Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted October 31, 2014 Author Report Share Posted October 31, 2014 The Akrapovic brand is likely the most well known exhaust brand in the world. The Movistar Yamaha MotoGP team uses Akrapovic exhausts along with the WSBK Aprilia factory team and the 2014 Daytona 200 winning Riders Discount Triumph team, just to name a few. Ask any two-wheeled enthusiast who makes the best exhaust and more often than not you'll hear them say Akrapovic. Check out the local bike night and you'll notice most bikes with an aftermarket exhaust will have an Akrapovic system installed. And now they make exhausts for your Honda Grom. This is a brand new exhaust for the Honda Grom and not yet listed on Riders Discount's website. If you would like to place an order, give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message through this forum or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! An Akrapovic exhaust for your Honda Grom will not only allow it to breathe better, but sound like a little monster when you open it up. Not only will it sound better, but your power and torque numbers will increase 4.5% over stock output. The Akrapovic exhaust for the Honda Grom is available as a full system or slip on with either a carbon fiber or titanium canister. The full system includes the slip on plus a titanium head-pipe weighing in at just under 3 lbs on our scale with the carbon fiber canister. Consider the stock system weighs about 11 lbs with the muffler alone at nearly 8lbs, this is a huge difference in weight. Check out that beautiful color change after breaking the exhaust in. Installation was a breeze. This is easily doable as long as you know how to turn a wrench. 30 minutes and a few bolts later, you have yourself a brand new Akrapovic exhaust installed. For just the slip on it's even easier as it is just the clamp and the muffler strap that need to be secured. This system is CARB compliant for California Grom owners, and meets EPA noise level requirements of 80dBA with the noise reducer installed. Everything necessary for installation is included with your order. Give us a call to order your exhaust system today! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted November 4, 2014 Author Report Share Posted November 4, 2014 If you're not too keen on the tinted taillight, Competition Werkes also has a clear lens available (pictured) or red for a more OE look. If you're interested in ordering this taillight kit, give MIKE a call at 866.931.6644 ext. 804 today! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted November 7, 2014 Author Report Share Posted November 7, 2014 Spiegler brake line kits are famous for excellent quality and custom fit installations. Each brake line is made to order utilizing any of their 81 color combinations of lines and fittings and is now available for the Honda Grom from Riders Discount. This brake line kit is not yet listed on the website but if you have any questions or would like to place an order, give MIKE a call at 866.931.6644 ext. 804. Is email more convenient? Send us a message through this forum or write to us at FORUM at RIDERSDISCOUNT dot COM, and we'll get back to you right away! Constructed from tightly-woven stainless steel tubing with DuPont PTFE-Teflon liners which resist expansion and increase your Grom's stopping power over the OE rubber brake hoses. Best of all they're backed by a lifetime manufacturer's warranty and DOT approved. Shown here with black lines, silver fittings, and black banjo bolts. We sell everything you need for your Honda Grom, if there's something you need just give us a call! Quote Link to comment Share on other sites More sharing options...
RidersDiscount Posted November 12, 2014 Author Report Share Posted November 12, 2014 Now that the Driven Rearsets are installed and having tried all the foot position options, we round that the bottom rear position was most comfortable for us. Obviously every rider is different but this was the majority vote for us at the Riders Discount office. Driven includes everything you need for the installation, including these spacers. If you would like to order these rearsets, give MIKE a call at 866.931.6644 ext. 804 today! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.