Stuff for sale

[desperado]

Since the truck isn't selling, and I need bucks for X-mas is sale time

 

 

1. MSD6BTM it's a MSD 6 with the turbo timing retard on it. New, never hooked up from what I can see. $250

http://www.jegs.com/webapp/wcs/stores/servlet/category2_10001_10002_17361_-1

 

2. MSD 6AL used, good working order $150

http://www.jegs.com/webapp/wcs/stores/servlet/category2_10001_10002_17361_-1

 

3. Holley Pro Dominator tunnel ram with 4150 (non-dominator top plate)

This is for a serious motor, low RPM street motors need not apply. Needs cleaned up and I will need to find the plugs for the holes that are drilled and tapped for the NOS fogger system currently on it. This is for a Small Block Chevy

$200 WITH OUT NOS KIT I do have a set of carbs for this but they will need assembled, additional cost for carbs.

http://www.jegs.com/webapp/wcs/stores/servlet/category2_10001_10002_15927_-1

 

4. NOS Pro Shot Fogger kit used. Will need a new hard line kit to install on your application, currently plumbed for the above intake. Will also need a Y splitter and shot lines to the fuel solenoids. With a 10 lb tank. $500

http://www.jegs.com/webapp/wcs/stores/servlet/category2_10001_10002_18775_-1

 

5. Holley Black pump used. Good shape $100

http://www.jegs.com/webapp/wcs/stores/servlet/category2_10001_10002_14235_-1

 

6. SBC TPI intake w/o injectors, used $100

All bolts except manifold to head are with it. No injectors. Great for a turbo setup with a Megasquirt. Has 9th injector. With underhood harness. Off a Camaro I believe similar to one listed on ebay here. http://cgi.ebay.com/ebaymotors/TPI-intake-manifold-corvette-350_W0QQcmdZViewItemQQcategoryZ36474QQihZ013QQitemZ230057179192QQrdZ1

 

7. SBC motor 355, complete except valve trane parts. Needs lifters, pushrods and rockers. Have ARP rocker studs for it. This was the motor out of the Cark. I have went through motor, it suffered a broken rocker stud and two bent push rods. Lower end is fine, from the looks of it, the bottom end was balanced. There has been significant work done on the crank. Pistons look to be Mahle forged units for visual matchup. 441 casting heads with minor port work done. I am selling as a long block, it will need an intake, carb and distribotor to be complete. $700

 

8. MSD crank triger for SBC used $175

http://www.jegs.com/webapp/wcs/stores/servlet/category2_10001_10002_17397_-1

 

9. 350 Turbo trannie w/ reverse valve body, full manual and brake. Have a 3600 RPM comvertor with it. $500

 

10. 1980 Monte Carlo drag car, tubed, caged. Needs tires and brakes. Roller, no engine or trannie. interior gutted, have title. $2000 OBO

 

11. 1980 Chevy Camaro Z28. Interior gutted caged, frame tied, full aluminium dash, 6 inch lift off cowl hood, 327 .30 over, 441 heads ported, 350 trannie with stage 3 shift kit. 12 bolt rear. This was a factory 4 speed Hurst car, rare. Race or restore. Will drive home, will need tires. Body is very straight, minor rust in rocker and right side front fender. Car is currently primered but will need sanded and painted. $5000 Firm. Many of you have seen this car, yuo oknow what it is.

 

12. Victor jr intake for SBC $150. Used but in great shape, bead blasted, ready to polish or bolt on. This is the preferred intake for a carb blow-through setup.

 

13. Stal pattern SBC headers off NASCAR motor. I have a set of standard flanges to go with these, paid a bunch of money for them, will bolt to AFR 7 bolt heads $200