Jump to content

Rear Brake Pads on my Nissan 350Z


POS VETT

Recommended Posts

My wife complained that the right rear brake on the Z has been squealing since a couple or so days ago and judging from the appearance of the outboard pads, they seemed to be a bit low.

 

So, today I decided to inspect the rear brakes. I jacked up the car, took off rear wheels, and disassembled the rear calipers to get the pads out. Here is a picture of them; the pair location correspond to their respective locations when mounted in the car.

 

http://i282.photobucket.com/albums/kk247/2003BlackZ06/Mobile%20Uploads/20140817_181507_zps8fa0a4ab.jpg

 

The pad thicknesses varied between 2 and 4 mm. There is only one pad (inboard right side) that has a wear indicator which explained the squealing only on the right side. It struck me as odd when there was only one pad with indicator, but it's probably not important.

 

Since there were still some friction material left, I decided to reuse the pads. However, I first rubbed the pads on my driveway concrete since I've heard this was a tried-and-true CR way to extend the life of brake pads. I made sure the pads were rubbed at the right angle relative to the rotor swept direction. Here is what I came with. Hopefully the rub marks are visible enough for you to see.

 

http://i282.photobucket.com/albums/kk247/2003BlackZ06/Mobile%20Uploads/20140817_181612_zps3de8210c.jpg

 

I hope I did it correctly although I have a couple questions. Should I have rubbed it on the swept direction also to achieve a cross-hatch pattern? I'm expecting to get roughly 5k more miles on them, but what can I do to get more life out of them?

 

Thanks for the help y'all, I'm a complete noob about this brake thing.

Link to comment
Share on other sites

I've read conflicting reports on the the cross hatching vs the way you did it.

 

It seems to be the consensus on the vw forums to NOT do the cross hatching. Lots of people drive their cars hard, but very few competitively autocross or HPDE it.

 

From my talks with recent SCCA members, and veteran auto crossers, they subscribe to the cross hatch pattern. They claim it gives the pad a more "virgin" surface to start with, yielding in a better initial bite.

 

Your wife probably falls into the first category, so I think you'll be fine.

Link to comment
Share on other sites

It's hard to tell what kind of concrete you have in the picture there. Depending on the surface's chemistry I can't say that you achieve enough positive transfer to prolong the life of the pads more than maybe 5k miles?

 

If you want to come by my lab we can throw them under the microscope and verify their structure has been sufficiently altered, I can even heat treat them for you and measure their hardness. Let me know.

Link to comment
Share on other sites

Damn man! I hadn't realized money was so tight at your house.

You know, it's not just about money, he's saving the environment, too. Each year in this country 3.3million car owners throw away brake pads just like these with lots of life left.

Link to comment
Share on other sites

No no no, the newest resolution is to buy 6 tubes of JB Weld, after performing the proper cross hatch pattern you mix up the tubes of JB and form about a 9mm brake pad surface. After proper cure time you can then perform the proper cross hatch pattern again taking off about 1 mm so they will be perfect t and good as new. the quality is clearly in the OEM backing plates of the pads anyway, so anything that gets to within 90% of the proper hardness spec will work properly for years to come.

 

Good luck, and if you need any help feel free to check back with us here at CR because we care.

Link to comment
Share on other sites

Dammit! I just did the RAV brakes this weekend! I had some pad left, too. I wish I would've seen this. I left my wear indicators on since I thought those were used in emergency stops to really dig in, so to speak. That's probably good since I forgot to cross hatch scratch my pads before reinstalling them. So, I'm good.
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...