Jump to content

ITT: Notchback content. Whats it worth?


AWW$HEEET

Recommended Posts

Ok, so while I am a noted Ford hater, I get wood for notchbacks. I would love a nice notch to go out and beat the dogshit out of some of you trolls. I have a possible trade situation for my Ducati Monster, but I need to know what this is worth. Here is his listing:

 

 

 

The Notch: 1989 5.0 black Notch 140,000 on chassis

Motor: 1991 302 bored over (306)

CRANK: forged crank polished

PISTONS: custom castings from Badger (hypertetic alloy)

LIFTERS: crane cams fast bleed roller

ROCKERS: crane cams roller 1.6

TIMING SET: double roller

CAM: crane not sure duration

OIL PUMP: svo high volume aluminum casting

cold air intake routed in fender.

T5 five speed tranny with Ford Racing clutch set and fly wheel.

GEARS: 3.73

CHASSIS: frame tied

SUPENSION: eiback lowering springs and shocks

all new tie rod ends.

Weld drag lites with 10"" slicks and 3" runners.

 

EXHAUST: shorty headers, off road H-pipe, magna flow mufflers with dumps

The notch is currently undergoing a clutch set install, the tranny just got back from Brians Transmission shop with a clean bill of health with all new seals installed.

The mustang is very fast with plenty of torque. May need rear control arm bushings. I was going to go with tubular with poly bushings. Summit has sets for under $300 for both upper and lower.

 

 

 

http://i207.photobucket.com/albums/bb275/Graveshaker/img1290892885998.jpg

 

http://i207.photobucket.com/albums/bb275/Graveshaker/img1290892885572.jpg

 

http://i207.photobucket.com/albums/bb275/Graveshaker/img1290648423760.jpg

Link to comment
Share on other sites

I have always loved them to. Nice looking cars. From what I have gathered they do hold a pretty good value, However you have to check them out alot are known for underside rust etc. You might want to get with Chad (On3Performance) as he does this for a living and knows his mustangs.
Link to comment
Share on other sites

3500-4500 depending how well that paint cleans up.

 

From his mouth:

 

Very slight rust above drivers rear tire. It hasn't showed it's face yet. One half dollar sized spot on drivers floor board (not a hole just starting to rust). I've been on my back under this car for a while working on the trans. Very clean undercarriage. No visible rust on the exterior. Looks as though the person who painted it last did not wet sand and buff, It does have orange peel. I never cared about the orange peel.

Link to comment
Share on other sites

Look for rust under the strut towers and right behind the front wheel wells. Also check the torque boxes were the rear upper control arms mount to the car.

 

 

If you go to look at it I will go with to help you out a bit.

 

Sweet deal, I would appreciate it. I don't wanna end up with some shit bucket.

Link to comment
Share on other sites

Good luck with that......everyone in the world thinks their notch is worth 10k

 

It apears to need the hood and front bumper painted, It only has a 306 with un spray friendly pistons, unknown cam and a week link t5. Only nice thing is if it is realy rust free. I sure as heck would not go above 5k

Link to comment
Share on other sites

Good luck with that......everyone in the world thinks their notch is worth 10k

 

That is true. Notches normally sell a lot faster and better than GT's or regular LX's. They do hold a bit better value than other fox body Mustangs and they are more desirable. I would say 4-5K MAX. From what you are saying it only has some bolt ons, no aluminum heads, stock intake etc. A similar car to this with heads and intake sold for for $6K on stangbangerz in the last week or so.

Link to comment
Share on other sites

You will be fine with the T5. You can break them with 300hp or they can hold 500hp for a while. It all depends. If you do break one, the rebuilt kit is $200 or you can find a T5 all day for about $300. Don't worry about it too much. It will hold the mods you have + 100 shot easy if it is fresh like the guy said.
Link to comment
Share on other sites

a stock 302 will break a t5 upgrade is a txo 500 or 600 or t56 if you want to run more gear

 

NO NO NO NO NO NO NO NO. People that break T5's behind stock 302's are the same people that don't know how to adjust an aftermarket shifter for a T5 and break shift forks.

Link to comment
Share on other sites

Why would anyone put hypereutectic pistons in a car with a forged crank? Almost sounds to me like someone didn't plan a build very well. If he skimped on the pistons then what else did he skimp on that you don't know about? Also, not knowing what cam is in it would worry me too. Unless you're planning on swapping it out for a known one.
Link to comment
Share on other sites

I think some of you are getting carried away with what Gabe wants. I beleive this is a SOLID car to start with for anyone not familiar with Mustangs, it has a decent body and the regular bolt ons that almost every Mustang is sold with.

 

 

Just go look at it and decide for yourself Gabe, these cars are very fun aand cheap to play around with.

Link to comment
Share on other sites

I would go for it!! looks like a solid car, if the frames tied through the floor you may want to pull the carpet up to check and see its all welded and painted and the front floor pans as well, I just traded my hatch mustang for a coupe and could not be happier!! also if you want a 4 inch harwood pin on i have one for it for 150 bucks, good luck with getting it, its a badass car
Link to comment
Share on other sites

Latest email from him, sounds shady:

 

I'm willing to go further with the deal but have to finish installing the new clutch and flywheel set. I only have limited time and opportunity to work on the car because of excessive work hours. I have the mustang over a friends house in his pole barn where we work on it when we have time. I got a strange vibration after a launch and initially thought it was the harmonic balancer. We installed a new balancer and still got a vibration. We then examined the car and discovered a cracked bell housing so we assumed this was causing the vibration. We swapped a good bell on the trans, bolted everything back up (without removing clutch and flywheel). To our surprise, the vibration was still present.

So now we've come to the conclusion that the vibration must be between the pressure plate and flywheel. Lesson learned to check everything while trans is out.

We've logically narrowed it down to clutch assembly and or flywheel based on parts replaced and the fact that the vibration is felt while standing still eliminating any other component. We've theorized one of the fingers in the pressure plate could be lose, dislodged spring on clutch disk or dislodged or loose flywheel weight. So back under the car I will have to go to remove the clutch assembly, inspect and replace any parts that's out of place. My biggest regret was not removing clutch assembly the first time and assuming all was good with the replaced bell.

 

I know this could sound scary but when it's all said and done, the mustang would have a new harmonic balancer, replaced bell, new seals on trans, new rear main seal and what ever needs replacing in the clutch assembly

Link to comment
Share on other sites

NO NO NO NO NO NO NO NO. People that break T5's behind stock 302's are the same people that don't know how to adjust an aftermarket shifter for a T5 and break shift forks.

 

Powershifting breaks gears in these. I've seen bad forks, but mine went on a 4K upshift from 2nd to 3rd. Not powershifting. Third gear was missing 3/4 of the teeth. The transmissions suck. People who like them can keep them. Give me a G-Force T-5 and I'd be fine.

There was a guy on here years ago that said that the T-45s were great as well. Then I heard him drive. Of course he wouldn't have issues when he was on and off the gas the way he was.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...