rl

I'm saying you need to verify the TDC mark on the balancer. Using a piston stop is the best way to do it. If you arent sure how then use Google and figure it out. It is very common for them to be off, I've seen them 30+ degrees off with aftermarket cranks and balancers.

There is no "one tooth off" on his car, as long as you have adjustment to within range the distributor is fine. Verify TDC with a piston stop, mark TDC, and set timing with a digital light that will allow you to set advance through the light. You sure you are on number 1 with the timing light? (Front left if looking at the motor) Are you sure you have the Spout out while checking timing?

Yes, I always just buy Mexican minutes, texts, and data through AT&T and use my phone as normal. I'm always near the coast though....

What time do the gates open and whats the layout of the event? (Testing time before qualification etc)

I'll be there.

I have AT&T and it always works in mexico.

Converter bolts where tight?

I have the same TV in my basement, a full paradigm setup, but I have Phantom v.3 towers in the front, A CC-270 center, and I forget what series rear satelites with a PDR-12 subwoofer. I love it, the only thing I would change with yours would be to move the fronts to the rear and get decent Floor standing paradigms with more range. Upstairs I have a pair of PDR-10's and one isnt enough but both turned down is perfect. Or if I feel like making my house into a club I can turn them up and knock stuff off the walls.

I'm pretty sure thats the German spelling of Italy.

Their effective displacement is larger and they produce a lot of exhaust volume at a high velocity.

thats on par for that boat, I know my 24' was the same way.

I'll get one, its simple. Just a valve and then a plastic T with a valve on the open end of the T so I can control how much air is brought in with the cleaner to help it atomize.

I seafoam my wifes every 3k and it stays squeeky clean (I peak at the open valves with a borescope every once and a while). When we first got it, it misfired it was plugged so bad. I just made a simple hose with a valve and a aerator and let it suck into the intake.

Thats right by my house, I drive the road daily. They must have been flying, its a 35mph zone with a round about. Not much to hit but some light poles. Almost no traffic.

I send 100+ a week USPS without issue, they havent lost anything in 2 years.

I use http://www.racepartsolutions.com unless you need cheapo pre-polished stuff, then Ebay. Local I dunno, Doesnt IPS have a mandrel bender?

I have a ton of pallets. A bunch of normal pallets (50+) and around 20 "odd" pallets (like 36"x76" with 2"x10" pine runners) I'd love to get rid of the odd ones. I normally burn them.

had you cleaned the filter with the cell since it was new? When they are new they can do that in a hurry.

The only way to know is to check.

I'll be there! Buddy of mine is going to run it as well.

I have a Portable classroom from a local school. It's basically a double wide trailer that is fairly open on the inside. It has dual HVAC units and has been used as a construction office for the last year. It's a 2003 model and in good shape ready to be pulled out (on 2 trailers obviously). If anyone shows interest I will post some pictures, this would make an awesome hunting cabin on property or on a lake somewhere. If I wasnt so busy thats what I would be doing with it. $6500 you come haul it out. I can have it transported but the cost would go up. It's probably worth close to that or more in scrap, each half has 8 axles under it.

I'll take it, sent you a PM.

I've been looking at them as well for the Wife. We are looking at 09+ TT's and these, I wish I could find a coupe thats AWD, so far they are all sedans and AWD.

Hopefully enough cars will show to make some of the 275 outlaw stuff happen...

All the events are in Xenia right? I'll make plans to be at all of them if there is a 6.50 class.