Dave1647545494

she was prolly to excited to think straight... you did the right thing though... graemlins/thumb.gif

Anyone have any experience with one of these? in terms of A-reliability B-out of the box performance C-availiable aftermarket parts I may go look for a new beater soon and one of these has caught my interest. thanks

I could do max and erma's. Havn't been there for awhile

CCR Dr Dre tons of other stuff I usually just click library on the media player and let it run when I'm using the computer

if its sitting a wilson and trabue with a busted out window and the colum ripped open it probably is stolen

I'd rock it. Big motor + little car = *** win

put some street tires on that thing and bring it out to a meet this summer. welcome

thanks for the replies I'll be in touch if this pile ever runs smile.gif

I have a 90 Trans AM 350 TPI I may be looking into a tune in the spring. does anyone do this local or should I just do a mail order chip?

ok he needs the yoke that bolts the rearend and the yoke that goes in the transmission. these can be purchased at jegs or found in the junkyard install both yokes on the truck with the ujoints in them and get an exact center to center measurement. then take the old driveshaft to a shop like columbus joint and clutch and they can shorten or extend your driveshaft and balance it. hth

thats awesome graemlins/thumb.gif

http://www.katyclassiccars.com/024c.jpg bet that chevelle runs sweet with the fuel lines laying right on the hot exhuast pipe. I hope whoever buys the car fixes it. It would really suck to have the whole car burn up from one little mistake like that. VERY nice pair of cars though. graemlins/thumb.gif

I've always gone to NTB on brice road. I lowered my shadow almost 4 inches swapped in a a 5spd and new axles all at the same time they got it dead on perfect. I can't find the bill but it was way under 100 dollars. They also did my Dakota after I dropped it 3" front 4" rear handled good and never any tire wear issues

so if this girl walks into your house and gets naked your going to kick her out, right? you'd hit that shit just as fast as anyone else would. Didn't your momma teach you its not nice to lie? smile.gif

I used an optima in my buick for about 2 months. just the strain of cranking over the motor killed it. I went back to a standard 1000 cca lead acid battery and havn't had a problem scince.

Bowling was a good time its worth the drive out. C ya next monday

fuck might as well stand outside the bar and arrest everyone who leaves then. good thing I usually drink at home

what is the legal limit right now? like say you weigh 185lbs how many drinks can you consume before you B.A.C. is too high? sucks you guys got whacked by a drunk too hope everyone was ok.

I was under the impression that with a prefabbed roll cage anyone could weld it in and then it would need certified by a chassis place or at the track by NHRA or IHRA staff or both depending on where your planning to race. try contacting BGBDBN on here he is an excellent welder with mobile welding capability.

made for pc 100/133 ram I have two 1 has onboard sound and video 1 has onboard sound and an Agp slot 20 dollars each

A Slovak man trapped in his car under an avalanche freed himself by drinking 60 bottles of beer and urinating on the snow to melt it. Rescue teams found Richard Kral drunk and staggering along a mountain path four days after his Audi car was buried in the Slovak Tatra mountains. thats fucking awesome smile.gif

I'm a Bengal fan and I'm glad the steelrs lost

I'm working on a 96 FZR right now hope to be ready to ride by spring smile.gif

heres another option you might consider. you cam buy a complete efi 360 (magnum) and 4spd trans from a junkyard for about 1200 dollars painless wiring makes a harness that makes it all work for around 300 bucks. a little bit of nitrous (500 bucks for a complete kit) and you'd have a fun easy on gas cruise anywhere car that runs low 12's pretty easy. there are also a slew of after market performance parts for the magnum engine. hth