jeffro

Don't tempt me. I have a stihl ms290 that needs a friend. I have not tried dicking with the fuel screws. No idea what I'm doing there. Might need to read up on it.

Tell them to get a job, then apply for financial aid through the school. No sense in spoon feeding.

Yes seriously, Homelite st-145. Looks like this. Received from my boss for free. Said it needed gas lines because it had been sitting for a while. Picked up the gas line rebuilt kit at TSC. This included the primer bulb (old one shatter when i pressed it) and gas line + fuel filter. Tore the carb down and cleaned it best i could with carb and choke cleaner. Gaskets looked okay so i put it back together with new primer bulb and fuel lines. Fired up first pull but seemed to be struggling when unchoked. Idled fine but died the instant i gave it throttle. Tore the carb down again to do some additional cleaning. Made sure all passage ways were clear and flowing freely. Removed needle valve and cleaned the rubber tip and passage way. Put everything back together and now it wont start at all. Any ideas? When reassembling the needle valve assembly it didnt seem like there was much travel. Primer bulb fills just fine with pressed.

And neither do you apparently. Enjoy the mechanical nightmare you just purchased, AGAIN.

Other two ladies single? :gabe: and yes, implying.

Dare i ask, how many miles?

I may have to go out and try this if I make it long enough

Sportsdevil is reliable, but quality suffers.

Noice. What was your exposure time on those night shots?

Made some time today to finish the aquarium stand. Sorry for potato quality pics. Started today by making a door. Took a 1x6, ripped it down to 1x2 actual. Cut a dado down the center and then cut the panel using the router table and a 1/2" straight but. The corners arent 100% but theyre pretty damn close. http://i.imgur.com/Ed9QJYj.jpg Took the body outside for a sand and paint. Aldo added corner trim to cover up the ugly looking rabbet joints. Used some brass hardware to hang the door and used a brass pull handle. The door latches via magnet. I found this dime sized magnet that is strong as hell so I counter-sunk it into the main body, then used a screw head on the inside of the door to give the magnet something to latch onto. Pretty much done at this point. http://i.imgur.com/wgnu09w.jpg And lastly, an unfocused photo i took in the dark of the stand with the tank on it. http://i.imgur.com/aiPrs8Q.jpg

Sportsdevil plugin or http://www.stream2watch.me /thread Disclaimer: adblockplus recommended for stream2watch.

still looking? Are these double headers?

well water > city water

Aquarium stand is coming along. So the plans i posted on Saturday were a bit off lol. Somewhere I left out a rabbet dimension or something and so everything was way too long (better than too short i guess). Last night i spent a good amount of time running dados and rabbets to get everything to snugly together. That router table i built earlier this year has really come in handy. Potato quality photo showing progress. The plan now is to sand everything, paint/stain(cant decide on a finish) then run corner trim down the corners to cover up the seems. Oh, and fix the door back on. http://i.imgur.com/MYoXZCK.png Note to self for future builds: ALWAYS ALWAYS ALWAYS double check board dimensions before assuming theyre equal. I picked up two pieces of 1x4x8 and only after gluing them found out that one was like 3.35" wide instead of 3.5.

Op wins the internet for the day. lols. Edit, last week. GLWS

Still, go straight to jail, do not pass go, do not collect $200.

:nopics:

Sounds like OP wants to run some sort of emulator inside of an n64.

Whatever is cheap lol. Probably the stuff that is finished on one side and not so much on the other.

Cutout Template for a sheet of plywood. This design is based on a 1/2" plywood. Its small enough that i doubt anything thicker would be necessary. Its too bad you cannot get 5X5 sheets here in the states. That would have been perfect to minimize scrap. http://i.imgur.com/EPnGr5P.png

Sister gave me a 10 gallon fish tank yesteday and it needs a stand. Decided to draw something up in autocad. Anyone who uses will CAD on a daily basis will probably have an aneurysm after seeing my dims, but whatever, it works for me. http://i.imgur.com/Fagh0dH.png

People want crazy dollars for working n64s. Non working is going to be your best bet.

I've got one. Shoot me an email and we can meet up Monday after 5pm in delaware.

"Old man accessories"