Buckeye1647545503 Posted December 31, 2006 Report Share Posted December 31, 2006 Did this kid used to own a orange Crx and was in the dispatch? Link to comment Share on other sites More sharing options...
Guest Removed Posted December 31, 2006 Report Share Posted December 31, 2006 Jeff Taylor Nissan Wannabe Location: Blacksburg, VA Posted: Sun Mar 26, 2006 4:22 pm Post subject: 528wHP / 420 wTQ on STOCK internals (the dyno vid) http://filebox.vt.edu/users/jetaylor/Jeff_KAT_Record.wmv if im lucky to get anywhere near that, then racing v8s will be a waste of gas. ok seen your vid and not impressed. you using spray? I'll race you with my v-8 , and IF you beat me i'll pay for your gas, but if i beat you, you have too pay for mine! Mines around $11 a gallon.C-16 isnt cheap. :burn: Link to comment Share on other sites More sharing options...
Guest powers Posted December 31, 2006 Report Share Posted December 31, 2006 hahahahahaha you left out bored? stroked? forged pistons? bushed or floating wrist pins? auto or manual if auto what converter? theres waaaaaaaaaaaaay more to building a fast car than just a couple of turbos I bet our young grasshopper will be 25 in a day or so I thought he said he was leaving the KA stock for now If I were to ask those questions they would be bored? bore rough size? what grit stone final hone? wall clearance? pistons 2016 or 4032? tool steel pins? Tapered? press fit or full float? double spiro or round locks? what size rings? ductle or moly coated top? gas ported? ceramic coated? teflon skirts? full skirt? gram weight dish cc? static compression ratio? dynamic compression ratio? copper bushed pin end? rod material 4340? or are you a baller and did better? h beam, or I beam? rod weight? tri metal bearings? babbet or no babbet? stroked? rod length? big end size? forged crank? 4340? or are you baller on this too? nitrided? heat treated? race prepped and by whom? who is balancing and to within what spec? who is assembling? head gasket o ringed, copper, or mls? what gasket sealant? studs are assumed, you get a pass on that one unless I asked you target clamping psi. these would be super to know if you are building the motor. Dear Coupe_no, I would love to hear your answers to the set up questions I posted. It would show all these nay sayers you KNOW what you are talking about. Serve em man. That would be super. You seem super. Thanks Link to comment Share on other sites More sharing options...
Guest powers Posted December 31, 2006 Report Share Posted December 31, 2006 http://members.shaw.ca/rbogdan/blog_images/gay_al.jpg THANX for asSking Link to comment Share on other sites More sharing options...
coupe_no Posted January 1, 2007 Author Report Share Posted January 1, 2007 you guys are boring Link to comment Share on other sites More sharing options...
Kevin R. Posted January 2, 2007 Report Share Posted January 2, 2007 you guys are boring Then leave. KTHNX. Link to comment Share on other sites More sharing options...
Primera Posted January 2, 2007 Report Share Posted January 2, 2007 you guys are boring You are uneducated Link to comment Share on other sites More sharing options...
Guest powers Posted January 2, 2007 Report Share Posted January 2, 2007 you guys are boring serve em man answer da lists i posted. That will show dem haterz. Link to comment Share on other sites More sharing options...
Linn1647545492 Posted January 2, 2007 Report Share Posted January 2, 2007 you guys are boring PM me when you have a running car, ill be more than happy to show you and your friends what the back of my camaro looks like. Link to comment Share on other sites More sharing options...
coupe_no Posted January 2, 2007 Author Report Share Posted January 2, 2007 ill be more than happy to show you and your friends what the back of my camaro looks like. just post a pic of it so i can locate you on the road I thought he said he was leaving the KA stock for now If I were to ask those questions they would be bored? bore rough size? what grit stone final hone? wall clearance? pistons 2016 or 4032? tool steel pins? Tapered? press fit or full float? double spiro or round locks? what size rings? ductle or moly coated top? gas ported? ceramic coated? teflon skirts? full skirt? gram weight dish cc? static compression ratio? dynamic compression ratio? copper bushed pin end? rod material 4340? or are you a baller and did better? h beam, or I beam? rod weight? tri metal bearings? babbet or no babbet? stroked? rod length? big end size? forged crank? 4340? or are you baller on this too? nitrided? heat treated? race prepped and by whom? who is balancing and to within what spec? who is assembling? head gasket o ringed, copper, or mls? what gasket sealant? studs are assumed, you get a pass on that one unless I asked you target clamping psi. no boring, i will hone it though, who cares what grit, pretty fine though cause i will be getting new rings prolly. ok im not worried about the rest i guess, ill be doing the assembling if i even take the block apart Link to comment Share on other sites More sharing options...
Tinman Posted January 2, 2007 Report Share Posted January 2, 2007 just post a pic of it so i can locate you on the road no boring, i will hone it though, who cares what grit, pretty fine though cause i will be getting new rings prolly. ok im not worried about the rest i guess, ill be doing the assembling if i even take the block apart I was giving you about 1/32 ounce of credit untill I read this post Link to comment Share on other sites More sharing options...
Guest Hal Posted January 2, 2007 Report Share Posted January 2, 2007 Instead of typing all that out and using the quote button all you needed to say was "I don't know Greg". And Linn posted a video, why would you need a picture. Link to comment Share on other sites More sharing options...
Mojoe Posted January 2, 2007 Report Share Posted January 2, 2007 Please look for this car on the road. Feel free to PM me when you are ready. Can I count on you for not later than mid May? http://i99.photobucket.com/albums/l284/dsnowgod/nightpics090.jpg Link to comment Share on other sites More sharing options...
Dr. Pomade Posted January 2, 2007 Report Share Posted January 2, 2007 Please page the second gunman on the grassy knoll. Link to comment Share on other sites More sharing options...
Miller Posted January 2, 2007 Report Share Posted January 2, 2007 lol where's the white towel? Link to comment Share on other sites More sharing options...
Linn1647545492 Posted January 2, 2007 Report Share Posted January 2, 2007 just post a pic of it so i can locate you on the road thats all you've got for me, i posted a video of my car what else do you need. your bench racing kills are lacking my young padawan. http://www.ejohnlove.com/blog_graphics/Jedi_John_Mitch_01_HI.jpg Link to comment Share on other sites More sharing options...
Guest powers Posted January 3, 2007 Report Share Posted January 3, 2007 just post a pic of it so i can locate you on the road no boring, i will hone it though, who cares what grit, pretty fine though cause i will be getting new rings prolly. ok im not worried about the rest i guess, ill be doing the assembling if i even take the block apart This post leads me to believe you could not put a block of LEGOs together Link to comment Share on other sites More sharing options...
Mattsv8 Posted January 5, 2007 Report Share Posted January 5, 2007 hey linn can i race your STOCK camaro so i can get a chance to race this kid with the imaginary car? PLease. Link to comment Share on other sites More sharing options...
Linn1647545492 Posted January 5, 2007 Report Share Posted January 5, 2007 hey linn can i race your STOCK camaro so i can get a chance to race this kid with the imaginary car? PLease. defenitly this spring, where did the newb go? Link to comment Share on other sites More sharing options...
996gangsta Posted January 6, 2007 Report Share Posted January 6, 2007 Wow this is very entertaining. How about racing for 1,000 dollars come spring? Link to comment Share on other sites More sharing options...
verse Posted January 6, 2007 Report Share Posted January 6, 2007 You might put in new rings? lol Don't try to pretend what you're talking about kid. We used to have kids like this in our Auto Tech classes at school. I just sat back and laughed at them. Link to comment Share on other sites More sharing options...
Primera Posted January 7, 2007 Report Share Posted January 7, 2007 How about racing for 1,000 dollars come spring? I feel bad for your dad's bank account Link to comment Share on other sites More sharing options...
Z06G Posted January 7, 2007 Report Share Posted January 7, 2007 I feel bad for your dad's bank account dad's bank account are you serious??? you obviously dont know him....i bet your car is soo fast too Link to comment Share on other sites More sharing options...
996gangsta Posted January 7, 2007 Report Share Posted January 7, 2007 I feel bad for your dad's bank account Interesting view point. Your such a clueless fool that I almost feel sorry for you. Sense you have such a big mouth how do you feel about racing me in my daily driver vs your g20. Link to comment Share on other sites More sharing options...
Primera Posted January 7, 2007 Report Share Posted January 7, 2007 dad's bank account are you serious??? you obviously dont know him....i bet your car is soo fast too Where'd I say my car was fast? I may be packing a whole 150-155whp OMG!! And that's after all the bolt-ons My bad for generalizing, it's just hard to see someone at a younger age having such a disposable piggy bank like that. What's your daily? Link to comment Share on other sites More sharing options...
Recommended Posts